Timewave PK-900 Operating Manual Download Page 12

Page: 12 / 392

CHAPTER 10 - SIGNAL IDENTIFICATION AND TDM OPERATION

Paragraph Page

10.1 Overview................................................... 10-1

10.2 SIAM Operation............................................. 10-1

10.2.1 Tuning In FSK Narrow and Wide Stations................ 10-2

10.3 Using the SIAM Mode........................................ 10-4

10.3.1 Copying Encoded RTTY Transmissions.................... 10-4

10.3.2 The CODE Command for International RTTY Compatibility. 10-5

10.4 TDM Receive Operation...................................... 10-5

10.4.1 TDM Parameters........................................ 10-5

10.4.2 Monitoring TDM Signals................................ 10-5

10.4.3 Where to Find TDM Signals............................. 10-6

CHAPTER 11 - PACTOR OPERATION

11.1 Overview................................................... 11-1

11.2 Where to Operate PACTOR.................................... 11-1

11.3 PK-900 Parameter Settings.................................. 11-2

11.3.1 Entering Your Callsign (MYPTCALL)..................... 11-2

11.3.2 Entering the PACTOR Mode.............................. 11-2

11.4 HF Receiver Settings....................................... 11-3

11.5 Tuning in PACTOR Stations.................................. 11-3

11.6 Operating on PACTOR........................................ 11-4

11.6.1 Going On the Air...................................... 11-5

11.6.2 Calling CQ in Unproto Mode............................ 11-5

11.6.3 Answering an Unproto PACTOR CQ........................ 11-6

11.6.3.1 Ending an ARQ PACTOR Contact..................... 11-7

11.6.4 Long Path Contacts.................................... 11-7

11.6.5 LCD Status and Mode Indicator......................... 11-8

11.7 PACTOR Operating Tips...................................... 11-9

11.7.1 ARQ Break-In (ACHG Command)........................... 11-9

11.7.2 Entering Your Auto-Answer Back (AAB).................. 11-9

11.7.3 Operating PACTOR on Other Modem Frequencies and Shifts 11-10

11.7.4 Automatic Speed Change................................ 11-10

11.7.5 Echoing Transmitted Characters As Sent (EAS).......... 11-10

11.7.6 Sending Only Complete Words (WORDOUT)................. 11-11

11.7.7 Operating on the Wrong Sideband....................... 11-11

11.7.8 Little Used PACTOR Commands........................... 11-11

11.8 Monitoring ARQ PACTOR Contacts with PTL.................... 11-12

11.9 PACTOR MailDrop Operation.................................. 11-12

11.9.1 Special Operating Considerations...................... 11-12

11.9.2 Settings For PACTOR MailDrop Operation................ 11-13

11.9.3 Starting PACTOR MailDrop Operation.................... 11-13

11.9.4 Local Logon to the MailDrop........................... 11-13

11.9.4.1 Remote Logon to your PACTOR MailDrop............. 11-13

11.9.5 Caller Prompts........................................ 11-13

11.9.6 Monitor MailDrop Operation............................ 11-14

11.9.7 SYSOP MailDrop Operation.............................. 11-14

3/93 TOC-8

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands