Timewave PK-900 Operating Manual Download Page 148

Page: 148 / 392

This forces a synchronization-lock, and starts the FAX displaying

regardless of what kind of signal is being monitored. Since this

synchronization lock was not sent by the transmitting station, the

picture will probably not be correctly positioned on the page.

Rather, it will likely appear to be split in half with the left half

of the picture on the right half of the page, and the right half of

the picture on the left half of the page.

To correct for this, a justification command has been included that

allows the user to shift the entire image to the left in 1/2 inch

increments. For example if the left-edge of the picture appears

roughly 4-1/2 inches away from the left edge of the paper, issuing the

command JUSTIFY 9 will shift the left edge of the picture to the left

4-1/2 inches (9 X 0.5 inch) correcting its justification.

The PK-900 will respond with:

JUstify now 9

This procedure will not be necessary if the PK-900 synchronizes from

the transmitted facsimile signal. This procedure is also not

necessary if you are using an AEA PAKRATT with FAX program. AEA

programs allow the image to be justified after it has been received.

To stop the display, you may either exit the facsimile mode by

changing to another mode or enter the RCVE command, which puts the

PK-900 back into facsimile standby receive. Standby receive is the

same as if you have just entered the FAX mode from another mode. The

PK-900 will wait until it receives the synchronization signal from a

facsimile station before beginning to display again.

9.6 Facsimile Operating Tips

If you are using an AEA PAKRATT WITH FAX program, consult the

program manual for more information and helpful hints.

9.6.1 Setting PRTYPE

Before FAX can be sent to your compute, you must choose the correct

"printer" type with the PRTYPE Command. AEA programs do this for you

automatically. The PK-900 defaults to the Epson format. See the

PRTYPE command in the Command Summary for the other types supported.

9.6.2 Printing Direction (LEFTRITE)

Weather FAX as well as most other facsimile displays from left to

right, but occasionally you may find a station that is reversed. If

you come across such a transmission, you may simply issue the command

LEFTRITE OFF to correct this. The PK-900 will respond with:

LEftrite now OFF

3/93 9-6

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands