Timewave PK-900 Operating Manual Download Page 339

Page: 339 / 392

PK-900 Gateway Option Supplement

The local TNC commands

CTEXT

CMSG

MTEXT

, and

MMSG

have no effect on Gateway

operation.

See the following pages for information about the new commands available to you
and enhancements to the current ones.

PACTOR & AMTOR operation with ARXTOR

The

ARXTOR

command has been added to enhance PACTOR operation. When

ARXTOR

is turned

, your DSP1232 will recognize either PACTOR or AMTOR link attempts.

In addition, when monitoring PACTOR stations with

PTLIST

, AMTOR stations will

also be heard if

ARXTOR

is also useful for those running the PACTOR or AMTOR Maildrop. When

ARXTOR

, remote stations can connect to your maildrop in either PACTOR or

AMTOR. See the

ARXTOR

command description later in this supplement for the full

details.

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands