manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 182 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 182

 

A.4       Controller Messages 

 

          From time to time, the PK-900 will generate messages informing you  

          of its status.  Error messages will also be generated if the PK-900  

          did not understand a command you have entered.  This section describes  

          the PK-900's messages and the circumstances which cause them. 

 

A.4.1     General Status Messages 

 

          Sign-On Message 

 

               AEA PK-900 Data Controller 

               Copyright (C) 1986 - 1992 by 

               Advanced Electronic Applications, Inc. 

               Release DD-MMM-YY 

               cmd: 

 

          The sign-on message appears when you turn on your PK-900, after  

          system "RESTART" or "RESET" after the autobaud routine.  The release  

          date is updated whenever the firmware is changed.  Please write the  

          date on the first page of this manual in case it is needed. 

 

               PK900 is using default values 

 

          This message appears the first time you turn on your PK-900 or every  

          time you turn the PK-900 on if the battery jumper is removed.  The  

          message will also appear in response to the RESET command. 

 

          cmd: 

 

          This is the Command Mode prompt.  When this prompt appears, the  

          PK-900 is waiting for you to issue a command.  Anything you type  

          after this prompt is interpreted as a command to the PK-900. 

 

          was 

          now 

 

          Whenever you change one of the PK-900's parameters, both the previous  

          value and the new value are displayed. 

 

          bbRAM scanned, checksum failed! 

 

          This message indicates there has been an error in the battery backed  

          RAM.  A low lithium battery is the likely cause for this. 

 

          ERROR: Subroutine,  Bank, Addr 

 

          This message indicates a program error has occurred.  Write down any  

          information accompanying this message and call AEA's Technical Support  

          department.  If possible, print a DISPLAY Z parameter listing. 

 

          ROM error, checksum $xxxx 

 

          This message indicates there has been a failure in the PK-900.  If  

          this message appears, call AEA's Technical Support department. 

 

 

 

1/93                                   A-4 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments