Timewave PK-900 Operating Manual Download Page 77

Page: 77 / 392

was the "A:*** CONNECTED" message from Port 2.

Now you want to let WX7EEE on VHF know that you are there, but that

you are involved in another QSO on HF. This way he will understand

that it may take you a little longer to respond to his packets.

Before you can send data to Radio Port 2, you must switch to this Port

with "|A" or the text you type will be sent to Radio Port 1.

You receive another packet from Jim on HF giving you a signal report

and describing his antenna. Again, the "0:" in front of the text

shows this was received on Port 1.

Now you want to give Jim a signal report so you must switch to Port 1

with |0 before your text or it will be sent to WX7EEE on Port 2.

After sending Jim a signal report, you tell your friend on VHF that

you want to go to the hamfest with him. You must switch back to

Port 2 by typing |A before sending to WX7EEE.

In the next received packet, we see that WX7EEE on VHF agrees to pick

you up at 8:00 to go to the hamfest. The "A:" in front of the packet

shows that this packet was received on Port 2.

Immediately following, you see a packet from Jim on HF saying it's

time to shut down. The "0:" identifies this as a Port 1 packet.

The last packet you sent was to WX7EEE on VHF so you decide to reply

to him first. This way you do not have to change Ports. After your

reply to WX7EEE, you change to Port 1 with |0 and send your good-byes

to Jim on HF.

Your friend WX7EEE on VHF says 73 and signs off with you. After two

stations agree to sign off, one of them must initiate a Disconnect.

You decide to disconnect from WX7EEE by first switching to Port 2 with

|A and then entering Command mode with a <Ctrl-C>. Once you see the

Command prompt (cmd:), enter the Disconnect "D" command.

Shortly after you do this you see the display

"*** DISCONNECTED: WX7EEE" from the PK-900.

Jim on HF has decided to initiate the disconnect with you so the final

packet you see is the "0:*** DISCONNECTED: WX1AAA" frame from Port 1.

4.8.3.3 More Thoughts on Port Switching

One problem of having more than one Radio Port is remembering which

port you are currently using. In the dual port sample QSOs above,

this was not a problem, but after it has been hours or days since you

have used your PK-900, you may forget which port you last used.

With AEA Pakratt Software programs, the on-screen status will always

show which port you are using so this is not a problem. With other

programs, you will have to query the PK-900 with the CSTATUS SHORT

command. The CSTATUS command displays the status of the logical

channels of Port 1 and Port 2 of the PK-900. The CSTATUS SHORT

command displays the status of the active channel and any other

connected packet channels. After completing the sample QSOs above,

the PK-900 would display the following.

1/93 4-35

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands