Timewave PK-900 Operating Manual Download Page 188

Page: 188 / 392

________________________________________________________________________________

8Bitconv ON|OFF Default: OFF

Mode: Packet, PACTOR, ASCII Host: 8B

_________________________________ Parameters: __________________________________

ON - The high-order bit IS NOT stripped in Converse Mode.

OFF - The high-order bit IS stripped in Converse Mode.

________________________________________________________________________________

8BITCONV permits packet and ASCII transmission of 8-bit data in Converse Mode.

When 8BITCONV is OFF (default), the high-order bit (bit seven) of characters

received from the terminal is set to 0 before the characters are transmitted.

________________________________________________________________________________

AAb text Default: empty

Mode: Baudot, ASCII, AMTOR, PACTOR Host: AU

_________________________________ Parameters: __________________________________

text - Any combination of characters up to a maximum of 24 characters.

________________________________________________________________________________

Use the AAB command to enter an acknowledgment text for Baudot, ASCII and AMTOR.

AAB sends automatic confirmation in Baudot, ASCII and AMTOR in response to a

distant station's WRU? request. Set WRU ON to activate Auto-Answerback in

ASCII and Baudot. In AMTOR and PACTOR, UserBIT 9 (UBIT 9) controls the Auto-

Answerback feature.

Type "AAB (24-character text)" to store your AnswerBack in memory.

________________________________________________________________________________

ABaud "n" Default: 110 bauds

Mode: ASCII Host: AB

_________________________________ Parameters: __________________________________

"n" - Specifies the ASCII data rate or signaling speed in bauds from your

PK-900 to your radio.

________________________________________________________________________________

ABAUD sets the radio ("on-air") baud rate only in the ASCII operating mode on

Radio Port 1. This value has no relationship to your computer or terminal

program's baud rate. The available "n" ASCII data rates in bauds are:

45, 50, 57, 75, 100, 110, 150, 200, 300, 400, 600, 1200, 2400, 4800 and 9600

________________________________________________________________________________

AChg Immediate Command

Mode: AMTOR, PACTOR Host: AG

________________________________________________________________________________

ACHG is an immediate command used in AMTOR and PACTOR by the receiving station

to interrupt the sending station's transmissions.

As the receiving station, you usually rely on the distant station, your part-

ner in the ARQ "handshake", to send the "+?" or PTOver command to do the

changeover. However, in ARQ (Mode A), or linked PACTOR, you can use the ACHG

command to "break in" on the sending station's transmission. Use the ACHG

command only when it is needed.

3/93 A-10

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands