manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 185 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 185

 

          too many packets outstanding 

 

          The message appears if you've typed enough data to fill the outgoing  

          buffer in either Converse or Transparent Mode.  You cannot re-enter  

          Converse or Transparent until some of the packets have been sent. 

 

          WARNING: Beacon too often 

 

          This Warning message appears if you have set the BEACON interval timer  

          to less than 90 (15 minutes) which is too often for busy channels. 

 

          WARNING: CHeck/FRack too small 

 

          This Warning message appears if you have set the CHECK timer for too  

          short a time relative to the FRACK timer. 

 

          WARNING: RESptime/FRack too large 

 

          This Warning message appears if you have set the RESPTIME timer for  

          too long a time relative to the FRACK timer. 

 

          WARNING: TXdelay too short 

 

          This Warning message appears if the TXDELAY timer has been set too  

          short to send at least one complete flag before the start of a packet. 

 

          WARNING: AUdelay > TXdelay 

 

          This Warning message appears if the AUDELAY timer has been set equal  

          to or greater than the TXDELAY timer. 

 

A.4.4     Packet Link Status Messages 

 

          Link status messages show you the status of AX.25 connections in which  

          your PK-900 is involved. 

 

          *** CONNECTED to: call1 [via call2[,call3...,call9]] 

 

          This message appears when your PK-900 switches to the connected  

          state.  

 

          *** Connect request:  call1 [via call2[,call3...,call9]] 

 

          Your PK-900 has received but not accepted a connect request from a  

          distant station. 

 

          *** DISCONNECTED: (call sign) 

 

          Your PK-900 has switched to the disconnected state.  This message  

          may be preceded by a message explaining the reason for the disconnect. 

 

          *** Retry count exceeded 

          *** DISCONNECTED: <call sign> 

 

          Your PK-900 has been disconnected because of a retry failure, rather  

          than a disconnect request from one of the stations. 

 

 

1/93                                   A-7 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments