Timewave PK-900 Operating Manual Download Page 291

Page: 291 / 392

PK-900 COMMAND LIST

COMMAND DEFAULT FUNCTION

3Rdparty OFF Enables 3rd party MailDrop messages

5Bit Immediate Command Starts copying special 5-bit stations

6Bit Immediate Command Starts copying special 6-bit stations

8Bitconv OFF Enables 8-bit data in packet/ASCII CONVERSE

AAb (empty) Sets the 0-24 character WRU Auto-answerback

ABaud 110 bauds Sets the ASCII baud rate

AChg Immediate Command Forces AMTOR and PACTOR ARQ Changeover

ACKprior OFF/OFF Enables priority acknowledgment in packet

ACRDisp 0 Sets terminal output Screen width

ACRPack ON Adds Carriage Returns to transmitted packets

ACRRtty 71 Sets the RTTY/AMTOR Auto <CR> insert column

ADelay 4 Sets AMTOR and PACTOR transmit delay, 10 ms.

AFilter OFF Enables All-mode receive character filter

ALFDisp ON Sends <LF> after <CR> to terminal

ALFPack OFF Sends <LF> after <CR> in transmitted packets

ALFRtty ON Sends <LF> after <CR> in transmitted RTTY

AList Immediate Command Starts the AMTOR ARQ 'Listen' mode

AMTOR Immediate Command Starts the AMTOR mode in ARQ standby

ANalog Immediate Command Starts the Analog mode

ANSample 2000 Sets the number of Analog mode samples

ARq (SELCAL) Starts the AMTOR ARQ call with SELCAL

ARQE Immediate Command Starts the ARQ-E receive mode

ARQTmo 60 Sets the AMTOR/PACTOR ARQ call time-out

ARQTOL 3 Sets bit jitter tolerance in ARQ AMTOR

AScii Immediate Command Starts the ASCII RTTY mode

ASPect 2 (576) Sets the received aspect ratio in FAX

AUdelay 2/2 (20 msec.) Sets delay before audio is applied after PTT

AUTOBaud OFF Enables Autobaud routine at every power-on

AWlen 7 Sets ASCII word length to RS-232 terminal

Ax25l2v2 ON/ON Sets AX.25 Version 2.0 packet protocol

AXDelay 0/0 (zero) Sets packet Repeater key-up delay (X10 ms)

AXHang 0/0 (zero) Sets packet Repeater hang time (X10 ms)

BARgraph 0 Sets the type of tuning bar graph display

BAudot Immediate Command Starts the Baudot RTTY mode

BBSmsgs OFF Enables TAPR style status messages

Beacon EVERY 0/EVERY 0 Sets the packet beacon timing (X10 seconds)

BItinv $00 Sets the XOR value to copy bit inverted RTTY

BKondel ON Sends <BS> <SP> <BS> for DELETE char.

BRight 50 Sets the brightness of the LCD backlight

BText (Empty) Sets the 120-byte packet BEACON message text

CALibrat Immediate Command Starts PK-900 AFSK tone calibrate mode

CANline $18 <CTRL-X> Sets the LINE DELETE character for editing

CANPac $19 <CTRL-Y> Sets the PACKET DELETE character for editing

CASedisp 0 (as is) Sets the display case (as is/lower/UPPER)

CBell OFF Enables packet and PACTOR 'Connect' bell

CCITT ON (Use the CODE COMMAND instead)

CFrom all/all Sets the Connect request/accept list

CHCall OFF Shows call sign after packet channel ID

CHDouble OFF Shows CHSWITCH character twice

CHeck 30/30 Sets Idle packet link time-out (X10 seconds)

CHSwitch $00 Sets the channel-select character

3/93 1

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands