Timewave PK-900 Operating Manual Download Page 15

Page: 15 / 392

CHAPTER 1

INTRODUCTION

1.1 Overview

The PK-900 was designed by AEA to provide you the Amateur the

complete digital operating position when coupled with a Personal

Computer or Computer Terminal. The PK-900 couples your HF or

VHF/UHF (or both) voice transceivers to your computer or terminal so

you can use its keyboard and display to "talk" to other Amateurs.

1.1.1 Capabilities

The PK-900 allows you to transmit and receive all legal Amateur

digital modes that are popular on both HF and VHF. In addition you

can send and receive black-and-white Weather FAX. The PK-900 can

receive other modes such as TDM, NAVTEX and bit-inverted Baudot RTTY.

These capabilities together with SIAM (Signal Identification and

Acquisition Mode) make the PK-900 ideal for the digital Short Wave

Listener as well.

The PK-900 with your Computer or Terminal allows you to transmit and

receive the following modes:

o AX.25 Packet, both HF and VHF (Chapter 4)

o Baudot and ASCII RTTY (Chapter 6)

o AMTOR/SITOR CCIR Rec. 476 and 625 (Chapter 7)

o Morse Code (Chapter 8)

o HF Weather FAX (Chapter 9)

o PACTOR (Chapter 11)

In addition the PK-900 receives the following modes:

o NAVTEX marine broadcasts (Chapter 7)

o TDM (Time Division Multiplex) signals (Chapter 10)

o Bit-inverted Baudot RTTY (Chapter 10)

The PK-900 also has the following special features:

o SIAM for SWLing (Chapter 10)

o PakMail Maildrop for Automatic Packet Message Handling (Chapter 5)

o AMTOR MailDrop Operation (Chapter 7)

o KISS mode for TCP/IP and special Packet applications (Appendix A)

o HOST mode for Host application programs (Technical Manual)

o Dualport operation with gateway (Chapter 4)

1.1.2 Included Components

Your PK-900 Data Controller package contains the following items:

o One PK-900 Data Controller

o PK-900 Operating Manual (this manual)

o Cables to connect your PK-900 to two separate radios

o Connector package to help set up your PK-900

o Radio Port "Loop-back" connector with jumper

o RS-232 Serial Cable with a DB-25 connector

3/93 1-1

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands