manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 295 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 295

 

  COMMAND      MNEMONIC            FUNCTION 

 

  TIme         $14 <CTRL-T>        Inserts the time (in DAYTIME) in text 

  TMail        OFF                 Enables AMTOR and PACTOR MailDrop 

  TMPrompt     (see text)          Sets an 80 character AMTOR MailDrop message 

  TRACe        OFF                 Enables a Hex dump of received data 

  Trans        Immediate Command   Enters the Transparent data mode 

  TRFlow       OFF                 Enables software flow control RX in Trans. 

  TRIes        0 (zero)            Displays or forces packet retry counter 

  TXDelay      30                  Sets the PTT key-to-data delay (X10 ms) 

  TXFlow       OFF                 Enables software flow control TX in Trans. 

  TXrev        OFF                 Reverses transmitted mark-space data sense 

  UBit         0                   Controls seldom used ON/OFF commands 

  UCmd         0                   Controls seldom used numeric commands 

  Unproto      CQ/CQ               Sets the UI packet frame sending Path/address 

  USers        1/1                 Sets allowed number of packet multi-connects 

  USOs         OFF                 Sets RTTY 'unshift on space' 

  Vhf          ON/ON               Selects VHF Packet - wide (1000 Hz) shift 

  VOltage      Immediate Command   Displays PK-900 critical voltage levels 

  WHYnot       OFF                 Displays reason why packet not displayed 

  WIdeshft     OFF                 Selects RTTY - wide or narrow (200 Hz) shift 

  WOrdout      OFF                 Sets Word output in RTTY/AMTOR/PACTOR modes 

  WRu          OFF                 Enables auto-answerback (AAB) in RTTY/ASCII 

  XBaud        0                   Sets 8530 baud rate to receive Baudot/ASCII 

  XFlow        ON                  Sets Software (XON/XOFF) RS-232 flow control 

  Xmit         Immediate Command   Starts sending Baudot/Morse/FAX transmission 

  XMITOk       ON                  Allows transmitter PTT line to be keyed 

  XOff         $13 <CTRL-S>        Sets character to stop sending received data 

  XON          $11 <CTRL-Q>        Sets character to start sending received data 

  ZFree        Immediate Command   Returns number of blocks of available memory 

  ZStatus      Immediate Command   Returns status of some internal parameters 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/93                                    5 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments