manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 186 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 186

 

          *** <call sign> busy 

          *** DISCONNECTED: <call sign> 

 

          Your connect request was rejected by a busy signal from another 

station. 

 

          FRMR sent: xx xx xx  or FRMR rcvd: xx xx xx 

 

          Your PK-900 is connected but a protocol error has occurred.  Your  

          PK-900 is trying to re-synchronize frame numbers with the distant  

          station's packet system.  The string xx xx xx is replaced with the hex  

          codes for the three bytes sent in the FRMR frame. 

 

A.4.5     MailDrop Error Messages 

 

          The following messages appear as a result of entering an invalid or  

          unrecognized command to the PK-900's MailDrop. 

 

          *** What? 

 

          You have entered a command that the MailDrop does not recognize. 

 

          *** Need callsign. 

 

          You have tried to send a message but not specified who you want to  

          send it to. 

 

          *** Message not found. 

 

          You have tried to List or Read message(s) that the MailDrop could not  

          find.  This also appears if you try to List messages when there are no  

          messages in your MailDrop. 

 

          *** No free memory. 

 

          You have tried to send a message, but the MailDrop does not have any  

          memory for more messages.  You must Kill messages to make room. 

 

          *** Not your message. 

 

          A remote user will get this when trying to read a message number that  

          is addressed to another station. 

 

          ?not while in (mode). 

 

          This message will be displayed if the "OK" command is entered when 

          the PK-900 is in any mode other than Signal. 

 

 

 

 

 

 

 

 

 

 

 

 

1/93                                   A-8 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments