manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 203 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 203

________________________________________________________________________________ 

     Beacon EVERY|AFTER "n"/EVERY|AFTER "n"  Default: EVERY 0/EVERY 0 (00 sec.) 

     Mode: Packet                            Host: BE 

_________________________________ Parameters: __________________________________ 

 

EVERY  -  Send the beacon at regular intervals. 

AFTER  -  Send the beacon after the specified time interval without activity. 

"n"    -  0 to 250 sets beacon timing in ten-second intervals. 

"0"    -  Zero turns off the beacon (default). 

________________________________________________________________________________ 

 

The BEACON command sets the conditions under which your beacon will be sent on  

each Radio Port. 

 

A beacon frame contains the text that you've typed into the BTEXT message in a  

packet addressed to the UNPROTO address.  When the keyword EVERY is specified a  

beacon packet is sent every "n" times ten seconds.  When AFTER is specified, a  

beacon is sent after "n" times ten seconds have passed without packet activity. 

 

If you set the BEACON timing less than "90" - a value judged as too short for  

busy channels - you'll see the following message at each command prompt: 

 

                    WARNING: BEACON too often 

 

Use Beacons with care and consideration for other users of the Packet channel. 

 

________________________________________________________________________________ 

     BItinv  "n"                                                 Default: $00 

     Mode:  RTTY                                                 Host: BI 

_________________________________ Parameters: __________________________________ 

 

"n"   -   0 to $1F, (0 to 31 decimal) specifies a number to be exclusive-ORed  

          with every received Baudot character.  BITINV 0 is plain text. 

________________________________________________________________________________ 

 

Bit inversion is used to prevent listeners from reading some commercial Baudot  

transmissions.  Usually either 2 or 3 bits of each character are inverted to  

give the appearance of an encrypted transmission.  Try different settings of  

BITINV on a Baudot signal after the baud rate has been determined.  If you are  

interested encrypted transmissions try experimenting with the 5BIT command. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/93                                   A-25 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments