Timewave PK-900 Operating Manual Download Page 162

Page: 162 / 392

o Wait a bit to see if you get a response. Your transmitter will

begin to key on and off and you will see a CONNECTED message when

someone calls you in ARQ PACTOR. If you do not get a response,

you can repeat the above procedure or you can go look for other

PACTOR stations as described in the next section.

11.6.3 Answering an Unproto PACTOR CQ

You must be in the PACTOR Listen (PTL) mode to monitor other PACTOR

stations. When you are in the PACTOR Listen mode, you can monitor

both the 1 second "chirps" of connected PACTOR stations, and the

continuous transmissions of unprotocol PACTOR stations calling CQ.

Normally when you see a station calling CQ in unproto PACTOR, you will

want to answer him using ARQ PACTOR. Remember that ARQ PACTOR is the

protocol that has the smallest chance of transmission errors.

Let's assume you hear N7ML calling CQ. To answer, do the following:

o If you are using an AEA PAKRATT for WINDOWS program, check the

program manual for instructions on starting an ARQ PACTOR

contact.

o If you are using a terminal or terminal emulation program, simply

type "PTC N7ML<Enter>" to start a linked or connected PACTOR

contact. After your PK-900 has locked or synchronized with the

distant station, which will be indicated by the LCD display

changing from PHASING to IDLE, you will see a CONNECTED message

on your screen. You may then begin your conversation.

N7ML DE YOURCALL...etc

o When you finish typing your comments or traffic to the other

station and wish to let the distant station transmit, you will

need to type "KKK" or "BTU" to let the other station know that

you are going to change the link direction.

o Then, type a <CTRL-Z> (Hold the "CTRL" key down while typing

the Z) to turn the link over to the other station.

<CTRL-Z> is the character defined by the PTOVER command that

switches your system from being the Information Sending

Station (ISS) to the Information Receiving Station (IRS) and

switches the distant system from being the information receiving

station to the information sending station.

The FCC requires station identification once every ten minutes. It's

sufficient to begin with "QRA (mycall)" or end your transmission with

"QRA (mycall)" before the <CTRL-Z> changeover code, or use the

<CTRL-B> "HERE-IS" to send your own Auto-AnswerBack message. For the

"HERE-IS" command to function, you must have your AAB text entered.

See appendix A for the AAB command.

3/93 11-6

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands