manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 268 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 268

_______________________________________________________________________________ 

     RFRame ON|OFF                                               Default: OFF 

     Mode: Baudot and ASCII RTTY                                 Host: RG 

_________________________________ Parameters: __________________________________ 

 

ON   -    Check received Baudot and ASCII characters for framing errors. 

OFF  -    Print received Baudot and ASCII characters regardless of errors. 

________________________________________________________________________________ 

 

When RFRAME is OFF (default), Baudot and ASCII modes operate as always, that is 

characters are copied based on the presence of the DCD signal. 

 

When RFRAME is ON, the PK-900 checks received Baudot and ASCII characters for 

framing errors.  A framing error on a character in an asynchronous mode  

(such as Baudot and ASCII) occurs when the bit in the stop position is detected  

to be the wrong polarity (the polarity of the start bit is supposed to be space  

or 0, while the stop bit is supposed to be mark or 1).  The unit stops copying  

characters when 4 out of the last 12 characters had framing errors.  Copy  

resumes when the most recent 12 characters are error-free.  This should  

significantly reduce the copying of garbage characters when no signals are  

present.  When RFRAME is ON, characters are copied based on the recent history 

of framing errors. 

 

 

________________________________________________________________________________ 

     RXRev ON|OFF                                                Default: OFF 

     Mode: Baudot and ASCII RTTY/AMTOR                           Host: RX 

_________________________________ Parameters: __________________________________ 

 

ON   -    Received data polarity is reversed (mark-space reversal). 

OFF  -    Received data polarity is normal. 

________________________________________________________________________________ 

 

Use the RXREV Command to invert the polarity of the data demodulated from the  

received mark and space tones. 

 

In some cases, you may be trying to copy a station that's transmitting "upside  

down" although it is receiving your signals correctly.  This is especially true  

when listening to signals in the Short Wave bands.  Set RXREV ON to reverse the  

data sense of received signals. 

 

Although RXR will reverse the mark and space polarity in PACTOR, the mode is  

polarity insensitive so RXR will have no effect. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/93                                   A-90 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments