Timewave PK-900 Operating Manual Download Page 325

Page: 325 / 392

PK-900 Gateway Option Supplement

040-067-9 — December 1993

PK-900

Gateway Option Supplement

Thank you for your purchase of Timewave’s Gateway firmware option for the
PK-900! Please read the enclosed sheet,

PK-900 EPROM Installation Instruction, for

instructions on how to install your new firmware.

New feature outline:

• Cross-mode Gateway includes packet/AMTOR, packet/PACTOR and packet/

packet operation. (See the new

GUSERS

and

XGATEWAY

commands for details).

• AEA packet “node” helps eliminate the need for digipeating.

• Enhanced AMTOR- and PACTOR-listen modes show link and connect at-

tempts.

• Automatic selection of AMTOR or PACTOR modes when a received signal is

tuned with the

ARXTOR

command.

• Enhanced packet

MHEARD

function identifies TCP/IP, NET/ROM and <The-

Net> stations.

•

MYALIAS

has been expanded to enable the “two-ham family” to use more than

one packet callsign with their PK-900.

• PACTOR “roundtable” operation has been enhanced with the

PTROUND

com-

mand.

• New

EXPERT

command now included so you’re no longer burdened with a large

number of commands to view.

• Full break-in CW operation is simplified with

MOPTT

• The

CODE

command has been epxanded to include the upper/lower case exten-

sions used by AMTOR MSO and APLINK stations.

• The SIAM (Signal) mode now indentifies PACTOR stations.

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands