manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 109 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 109

 

          The Radio Port 2 modems are: 

 

          MODEM  1  AFSK Modem, 200  Hz shift, Mark=1270 Hz, Space=1070 Hz 

          MODEM  2  AFSK Modem, 200  Hz shift, Mark=2225 Hz, Space=2025 Hz 

          MODEM  3  AFSK Modem, 1000 Hz shift, Mark=1200 Hz, Space=2200 Hz 

          MODEM  4  AFSK Modem, 1000 Hz shift, Mark=1200 Hz, Space=2200 Hz eq 

          MODEM  5  AFSK Modem, 200  Hz shift, Mark=980  Hz, Space=1180 Hz 

          MODEM  6  AFSK Modem, 200  Hz shift, Mark=1650 Hz, Space=1850 Hz 

          MODEM  7  AFSK Modem, 800  Hz shift, Mark=1300 Hz, Space=2100 Hz 

          MODEM  8  AFSK Modem, 800  Hz shift, Mark=1300 Hz, Space=2100 Hz eq 

          MODEM  9  AFSK Modem, Direct FSK 9600 baud internal option. 

          MODEM 10  Modem disconnect header External option, user supplied. 

 

6.7.1     Selecting Modems 

 

          The various modems available in the PK-900 can be seen with the 

          DIR(ectory) command.  To display all the available modems simply  

          enter the Command Mode of the PK-900 and then type DIR as shown. 

 

                   DIR <Enter> 

 

          The PK-900 will respond with the following: 

 

           - Port 1 -                              - Port 2 - 

      1: FSK 45 bps 170: 2125/2295            1: Internal 200: 1070/1270 

      2: FSK 100 bps 170: 2125/2295           2: Internal 200: 2025/2225 

      3: FSK 45 bps 200: 2110/2310            3: Internal 1000: 1200/2200 

      4: FSK 100 bps 200: 2110/2310           4: Internal 1000: 1200/2200 eq. 

      5: FSK 100 bps 425: 2125/2550           5: Internal 200: 1180/980 

      6: FSK 100 bps 850: 2125/2975           6: Internal 200: 1850/1650 

      7: FSK 100 bps 850: 1275/2125           7: Internal 800: 2100/1300 

      8: Analog 900/2500                      8: Internal 800: 2100/1300 eq. 

      9: FSK 2400 bps 800: 1300/2100          9: Internal option 

     10: FSK 300 bps 200: 2110/2310          10: Modem disconnect header 

     11: FSK 1200 bps 1000: 1200/2200 

     12: Morse 750 

     cmd:    

 

          Any modem from the list may be loaded with the MODEM command, but  

          only Radio Port 1 modems 1 through 7 and 10 should be used for   

          Baudot or ASCII RTTY. 

 

          For example, to operate 45 baud Baudot on radio port 1 and 1200 bps  

          VHF packet on radio port 2 you must load modem 1/4.  To load modem  

          1 from Radio Port directory 1 and modem 4 from Radio Port directory 2,  

          first enter the Command Mode  and then type MODEM 1/4 as  

          shown below: 

 

                   MODEM 1/4 <Enter> 

 

          The PK-900 will respond with the following: 

 

                    MODem was  x/x  (will show previous modems) 

                    MODem now  1/4 

 

          When starting Baudot or ASCII RTTY operation, the PK-900 defaults to 

 

 

3/93                                    6-11 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments