Timewave PK-900 Operating Manual Download Page 246

Page: 246 / 392

________________________________________________________________________________

Monitor "n/n" Default: 4/4 (UA DM C D I UI)

Mode: Packet Host: MN

_________________________________ Parameters: __________________________________

"n" - 0 to 6 signifies various levels on monitor indications

________________________________________________________________________________

The Monitor command determines what kind of packets on each Radio Port are

displayed when the PK-900 is NOT connected to any other packet stations.

The meanings of the parameter values are:

0 All packet monitoring functions are disabled.

1 Only unnumbered (UI) frames resulting from an unconnected transmission are

displayed. Use this for an "unproto," round-table type QSO. This

setting also displays beacons.

2 Numbered (I) frames are also displayed. I-frames are numbered in order of

generation and result from a connected transmission. Use this to monitor

connected conversations in progress.

3 Connect request (SABM or "C") frames and disconnect (DISC or "D") frames

are also displayed with the headers.

4 Unnumbered acknowledgment (UA) of connect- and disconnect-state frames are

also displayed with either the characters "UA" or "DM" and a header.

5 Receive Ready (RR), Receive Not Ready (RNR), Reject (RJ), Frame Reject

(FRMR) and (I)-Frames are also displayed.

6 Poll/Final bit, PID and sequence numbers are also displayed.

________________________________________________________________________________

MOrse Immediate Command

Mode: Command Host: MO

________________________________________________________________________________

MORSE is an immediate command that switches Radio Port 1 of your PK-900 into

the Morse mode.

Unless you change MSPEED, your PK-900 uses the default Morse transmit speed

value of 20 WPM.

1/93 A-68

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands