manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 38 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 38

 

3.4.2     PK-900 Connections 

 

          Remove power from the PK-900, your transceiver and all accessories  

          before making any connections. 

 

          Connect the radio cable(s) you constructed in section 3.3.5 between a  

          Radio port on the PK-900 and your transceiver(s). 

 

          If you wired cables for CW keying or Direct FSK then connect these to  

          the appropriate point on your equipment. 

 

 

3.5       Transceiver Adjustments 

 

          This section is split into separate procedures for FM and SSB radios. 

          You may adjust either port at any time without affecting the other. 

 

3.5.1     FM Transceiver Final Adjustments 

 

          1.   Turn on your computer and PK-900 and start your terminal  

               program. 

 

          2.   Connect the radio to a dummy load.  Be prepared to monitor your  

               transmissions with another nearby radio such as a handheld  

               transceiver. 

 

          3.   Verify that your PK-900 and FM radio are connected as shown in  

               Figure 3-5 below. 

 

 

                   Figure 3-5  Radio-to-PK-900 Connections 

 

          4.   If you are using an AEA program such as PC-PAKRATT II or MACRATT,  

               you must enter the Dumb Terminal mode to access the CALIBRATE  

               Mode as described below. 

 

          5.   Enter the Calibrate mode by typing: "CAL <Enter>." 

 

          NOTE:     In the Calibrate mode only, the "K" key toggles the  

                    transmitter PTT line on and off.  The "SPACE BAR" toggles  

                    the PK-900's tone generator from "Mark" (the lower pitched  

                    tone) to "Space" (the higher pitched tone).  The PK-900  

                    has a transmit watchdog timer circuit that unkeys your  

                    transmitter automatically after sixty (60) seconds.  As you  

                    perform the following adjustments, unkey periodically, then  

                    rekey the transmitter by typing "K." 

 

1/93                                    3-8 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments