Timewave PK-900 Operating Manual Download Page 193

Page: 193 / 392

________________________________________________________________________________

ALFPack ON|OFF Default: OFF

Mode: Packet Host: AP

_________________________________ Parameters: __________________________________

ON - A <LF> character IS added after each <CR> sent in outgoing packets.

OFF - A <LF> is NOT added to outgoing packets (default).

________________________________________________________________________________

ALFPACK is similar to ALFDISP, except that the <LF> characters are added to

outgoing (transmitted) packets, rather than to text displayed locally.

o If the person you are talking to reports overprinting of packets from your

station, set ALFPACK ON. ALFPACK is disabled in Transparent Mode.

________________________________________________________________________________

ALFRtty ON|OFF Default: ON

Mode: Baudot/ASCII RTTY Host: AR

_________________________________ Parameters: __________________________________

ON - A line feed character <LF> IS sent after each carriage return <CR>.

OFF - A <LF> is NOT sent after each <CR>.

________________________________________________________________________________

If ALFRTTY is set ON when transmitting Baudot or ASCII RTTY, a line feed

character is added and sent automatically after each <CR> character you type.

Use this option when you are typing into the transmit buffer and don't want to

be bothered worrying about line length. You should NOT use this option when

retransmitting text received from another station; for example, ARRL Bulletins.

o ALFRTTY has no effect in AMTOR; a line feed is automatically added after

each carriage return.

________________________________________________________________________________

AList Immediate Command

Mode: AMTOR Host: AL

_______________________________________________________________________________

ALIST is an immediate command that switches your PK-900 into the ARQ Listen

mode.

You can usually monitor an ARQ AMTOR contact between two linked stations using

the ARQ Listen mode (also called Mode L). This mode may need a few seconds to

phase or acquire synchronization with the other stations. Your ability to

synchronize with the master station depends on operating conditions such as

interference. Since you are not part of the "error free" link, your monitor

will display retries that occur if the two linked stations you are monitoring

experience ARQ errors.

Type ALIST (or AL) repeatedly if you lose synchronization.

1/93 A-15

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands