manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 106 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 106

 

6.5.9     Operating at Commercial or VHF Wide RTTY Shifts 

 

          Most commercial stations found in the non amateur Short Wave bands  

          operate with a wide Frequency Shift keying of either 425 or 850 Hz  

          shift.  To allow these stations to be received other modems are  

          available in the PK-900 and can be selected with the MODEM command.   

          The following modems are available for Baudot and ASCII operation: 

 

                              Radio Port 1 Modems    

 

             MODEM  1  AFSK Modem, 170 Hz shift, M 2125 Hz, S 2295 Hz, 45  bps 

             MODEM  2  AFSK Modem, 170 Hz shift, M 2125 Hz, S 2295 Hz, 100 bps 

             MODEM  3  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz,  45 bps 

             MODEM  4  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz, 100 bps 

             MODEM  5  AFSK Modem, 425 Hz shift, M 2125 Hz, S 2550 Hz, 100 bps 

             MODEM  6  AFSK Modem, 850 Hz shift, M 2125 Hz, S 2975 Hz, 100 bps 

             MODEM  7  AFSK Modem, 850 Hz shift, M 2125 Hz, S 1275 Hz, 100 bps 

             MODEM 10  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz, 300 bps 

 

          If your license permits, you can also transmit to these stations when  

          the appropriate MODEM number and data rate is selected. 

 

6.5.10    The CODE Command for International RTTY Compatibility 

 

          The CODE command allows the PK-900 to receive (and sometimes send)  

          other RTTY character sets.  Part 97.69 of the FCC rules specifies that  

          the International Telegraph Alphabet Number 2 (ITA #2) must be used by   

          U.S. stations when operating RTTY.  This corresponds to the CODE 0  

          command (default), but you may want to see the CODE command for more  

          information on the capabilities of your PK-900. 

 

6.5.11    Copying Encoded RTTY Transmissions 

 

          In the Short Wave bands many RTTY stations can be found that are not  

          transmitting in plain text.  Most of these stations are using  

          sophisticated encryption techniques that make receiving them almost  

          impossible.  There are a few stations however that use a relatively  

          simple bit-inversion technique to make them hard to copy.  For these  

          stations, the PK-900 has included the BITINV command to allow the  

          SWL to decode these simple forms of encoded RTTY stations. 

 

 

6.6       ASCII RTTY Operation 

 

          ASCII RTTY operation is almost identical to Baudot operation but there  

          are a few differences you must know.  Because the ASCII code uses  

          seven bits to define a character (instead of the five bits used in the  

          Baudot/Murray code), the probability of receiving errors is somewhat  

          higher.  For these reasons, ASCII is not used widely on the HF amateur  

          bands.  However, some commercial and military HF stations as well as  

          W1AW do use ASCII. 

 

6.6.1     Starting ASCII Operation 

 

          First you must enter the ASCII mode of the PK-900. 

          If you are using an AEA PAKRATT program, follow the instructions in  

          the program manual to enter the ASCII mode. 

 

1/93                                   6-8 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments