manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 374 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 374

2

TIMEWAVE TECHNOLOGY INC.

LIMITED ONE YEAR WARRANTY

This warranty is extended only to the original purchaser of the A.06265.

If your A.06265 fails in normal use because of a defect in workmanship or
materials within one year of the date of purchase, we will repair or replace (at our
option) the equipment at our factory without charge to you.  Timewave will pay
for the return of the warranty-repaired unit to you.

First, double check your connections and operating procedure.  If you're certain
that the unit is faulty, notify Timewave Customer Service immediately.  If
Timewave is unable to resolve the problem by telephone or email, we will give
you an RMA number and ask you to return the unit.  You must pay all shipping
and insurance charges for returning the unit to our factory.

We cannot be responsible for damage caused by accidents, abuse, misuse,
improper installation, or unauthorized attempts to repair the unit. This warranty
does not cover any parts of the PK-900 except the A.06265.

Timewave service work performed in connection with this warranty is warranted
to be free from defects in materials and workmanship for 30 days from the date
of rerpair. All other terms of the limited warranty apply to the service warranty.

Contact Timewave Customer Service by telephone at (651) 489-5080 or  by FAX
at (651) 489-5066.

Mailing and shipping address:

Timewave Technology Inc.
501 W. Lawson Ave.
 St.Paul, MN 55117

email:

[email protected]
[email protected]
[email protected]

web:

www.timewave.com

TIMEWAVE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

WARRANTY

WHO IS COVERED

WHAT WE WILL DO

WHAT YOU MUST DO

WHAT IS NOT
COVERED

SERVICE WARRANTY

HOW TO CONTACT
TIMEWAVE

©2002  by Timewave Technology Inc., St. Paul, MN USA

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments