Timewave PK-900 Operating Manual Download Page 126

Page: 126 / 392

The first way is automatic:

Your MailDrop will send "STAND BY" and then the WRU request to the

remote user. Always be sure you have entered a proper Auto-Answerback

(AAB) message consisting of "QRA YOURCALL YOUR_MYSELCAL YOUR_MYIDENT"

as described earlier in this chapter.

The second way covers beginning AMTOR users:

AMTOR users who have not entered a proper Auto-AnswerBack response or

for some reason have the WRU feature disabled cannot be automatically

identified by your MailDrop. In this case, your MailDrop will ask the

calling station to identify as follows:

After 10 seconds your MailDrop will ask the calling station to

identify by sending "QRZ? DE your c?" to the calling station.

The calling station then has 3 minutes to respond with its callsign.

The ID must contain either "QRA" or "DE" and must end with "+?".

An Amateur with the call WX7BBB would send the following:

QRA ?

If no satisfactory ID occurs within 3 minutes from the establishment

of the link, the link is automatically shut down.

The third way covers experienced users:

Experienced AMTOR users may want to save time by simply sending QRA

followed by their callsign immediately after establishing the link.

For example station WX7BBB may simply enter the following immediately

after establishing the ARQ link.

QRA ?

The PK-900 then sends the user the MTEXT string if the MailDrop

message command (MMSG) is ON. The default text is shown below:

WELCOME TO MY AEA PK-900 MAILDROP.

TYPE H FOR HELP.

7.6.5 Caller Prompts

The command prompt that the MailDrop sends the remote user in AMTOR is

shortened from that used in the Packet mode and is shown below:

WX7BBB DE WX7AAA GA+?

TMPROMPT is the AMTOR MailDrop message prompt sent to a remote station

by your MailDrop. The default prompt is:

GA subj/GA msg, '/EX' to end.

Text before the first slash is sent to the user as the subject prompt;

text after the slash is sent as the message text prompt.

1/93 7-12

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands