Timewave PK-900 Operating Manual Download Page 116

Page: 116 / 392

The PK-900 will tell you, MYSelcal now NNML

See the MYSELCAL command in the Command Summary if you are interested

in more information on the translation process.

Because the same call sign sequences are assigned in ten US districts,

it is possible that your SELCALL could be used by another station. If

you think a station in another call district is also active on AMTOR

and is using the same SELCALL, see the MYSELCAL command for

information on how to change your Selcall.

7.2.3 Entering Your Selective calling Code (MYIDENT)

At the present time, most of the AMTOR activity on the amateur bands

is using the four-character SELCALL defined in CCIR 476 and described

above. The seven-character SELCALL (MYIDENT) defined in CCIR 625

solves the problem of non-unique SELCALLs by providing many more

possible SELCALLs than CCIR 476 does with only four characters.

To enter your seven-character SELCALL all you must do is enter your

amateur callsign. The PK-900 will do the translation for you.

If you are using an AEA PAKRATT program, follow the instructions in

the program manual for entering the command MYIDENT.

If you are using a terminal, then enter the following

cmd:MYIDENT N7ML

The PK-900 will tell you, MYIdent now VTMFFFF

See the MYIDENT command in the Command Summary if you are interested

in more information on the translation process.

7.2.4 Enter the AMTOR Mode

Now that you have entered your personal MYSELCAL and MYIDENT Selective

Calling codes, you are ready to enter the AMTOR mode.

If you are using an AEA PAKRATT program, follow the instructions in

the program manual to enter the AMTOR mode.

If you are using a terminal, simply type "AMTOR" or "AM" from the

Command Mode followed by the <Enter> key to enter the AMTOR mode.

The PK-900 responds by displaying the previous mode:

Opmode was PAcket

Opmode now AMtor

Your PK-900's front panel LCD Status display will show that you are in

the AMTOR Standby mode on Radio Port 1, and the COMMAND LCD will be

lit.

7.2.5 HF Receiver Settings

Set your HF receiver (or transceiver) to Lower Sideband (LSB) unless

you connected your PK-900 through the direct FSK keying lines.

1/93 7-2

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands