manualshive.com logo in svg

Timewave PK-900, Operating Manual

The Timewave PK-900 operating manual is a comprehensive guide designed to help users effortlessly navigate this high-performance product. Offering step-by-step instructions and expert tips, this manual is available for free download at manualshive.com. Unlock the full potential of your Timewave PK-900 with this essential and user-friendly manual.

Share
Download
background image

 

          send the AAB message when another station requests your identity, and  

          then stop sending. 

 

 

7.4.3     Operating AMTOR with Other Modem frequencies and Shifts 

 

          All Amateur (AMTOR) and commercial (SITOR) stations that we know of 

          use either 170 or 200 Hz shift FSK modems.  Modem 2 (default) is 

          therefore the best choice for ARQ or FEC AMTOR use.  The PK-900  

          allows other modems to be used in AMTOR should the need arise.  The  

          following other modems may be selected with the MODEM command. 

 

       Radio Port 1 Modems    

 

             MODEM  1  AFSK Modem, 170 Hz shift, M 2125 Hz, S 2295 Hz, 45  bps 

             MODEM  2  AFSK Modem, 170 Hz shift, M 2125 Hz, S 2295 Hz, 100 bps 

             MODEM  3  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz,  45 bps 

             MODEM  4  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz, 100 bps 

             MODEM  5  AFSK Modem, 425 Hz shift, M 2125 Hz, S 2550 Hz, 100 bps 

             MODEM  6  AFSK Modem, 850 Hz shift, M 2125 Hz, S 2975 Hz, 100 bps 

             MODEM  7  AFSK Modem, 850 Hz shift, M 2125 Hz, S 1275 Hz, 100 bps 

             MODEM 10  AFSK Modem, 200 Hz shift, M 2110 Hz, S 2310 Hz, 300 bps 

 

 

7.4.4     Speed Change Not Permitted 

 

          In accordance with FCC 97.69 and international regulations, AMTOR is  

          operated at 100 bauds.  The PK-900 does not permit other speeds.  For  

          that reason, Modems 1 and 3 are not recommended. 

  

7.4.5     Echoing Transmitted Characters As Sent (EAS) 

 

          EAS has special significance in ARQ AMTOR.  If EAS is ON, you will see  

          characters echoed to your screen only after your partner in the AMTOR   

          link, has validated the previous block.  With EAS ON, the characters  

          appear on your screen three at a time. 

 

          o    If the data scrolls across your monitor at an even rate, you can  

               assume that you have a good ARQ link. 

 

          o    If the data hesitates or scrolls in "jerky" intermittent fashion, 

               that's generally a sign that the radio link is not very good. 

 

          o    If the characters stop appearing on your monitor, the link is  

               failing or has failed.  The LCD Status display will tell you this 

               by showing ERROR or REQUEST nearly continuously. 

 

7.4.6     Sending Only Complete Words (WORDOUT) 

 

          Some AMTOR users like to have their words sent out only when they are  

          complete.  This allows the word you are currently typing to be edited  

          as long as you have not typed a <Space> character.  Turning WORDOUT ON  

          activates this feature.  See the Command Summary for more information. 

 

 

 

 

 

1/93                                   7-9 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments

Related manuals for PK-900

Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
ICP DAS USA MDC-700 Series Quick Start preview
MDC-700 Series
Brand: ICP DAS USA Pages: 4
ICP DAS USA I-7080 Quick Start Manual preview
I-7080
Brand: ICP DAS USA Pages: 6
ICP DAS USA EIP-2000 Series Faq preview
EIP-2000 Series
Brand: ICP DAS USA Pages: 19
jbc DDE-1B Manual preview
DDE-1B
Brand: jbc Pages: 44
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
Rain Bird Image Series Quick Start Manual preview
Image Series
Brand: Rain Bird Pages: 4
Rain Bird ESP-ME3 Quick Reference Manual preview
ESP-ME3
Brand: Rain Bird Pages: 2
Rain Bird ESP-Me User Manual preview
ESP-Me
Brand: Rain Bird Pages: 140
Raindrip WeatherSmart RSC600i Installation & Programming preview
WeatherSmart RSC600i
Brand: Raindrip Pages: 36
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Brand: Rain Bird Pages: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Brand: Rain Bird Pages: 16
Rabe PILOT Original Instructions Manual preview
PILOT
Brand: Rabe Pages: 61
Racal Instruments 1260 VXI Instructions Manual preview
1260 VXI
Brand: Racal Instruments Pages: 35
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Brand: Zener Pages: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Brand: Zapi Pages: 5
ZKTeco MA500 Installation Manual & User Manual preview
MA500
Brand: ZKTeco Pages: 20

Brands by name

Popular brands

Load more brands