Timewave PK-900 Operating Manual Download Page 221

Page: 221 / 392

________________________________________________________________________________

DELete ON|OFF Default: OFF

Mode: All Host: DL

_________________________________ Parameters: __________________________________

ON - The <DELETE> ($7F) key is used for editing your typing.

OFF - The <BACKSPACE> ($08) key is used for editing your typing.

________________________________________________________________________________

Use the DELETE command to select the key to use for deleting while editing.

Set DELETE OFF (default) if you wish to use the <Backspace> key to edit typing

mistakes. Set DELETE ON if you wish to use the <Delete> key to edit mistakes.

See the BKONDEL command controls how the PK-900 indicates deletion.

________________________________________________________________________________

DFrom all,none,yes/no call1[,call2..] / all,none,yes/no call1[,call2..]

Default: all/all

Mode: Packet Host: DF

_________________________________ Parameters: __________________________________

call - all, none, YES list, NO list.

list of up to eight call signs, separated by commas.

________________________________________________________________________________

DFROM determines how each Radio Port of your PK-900 responds to stations

trying to use your station as a digipeater. DFROM is set to "all/all" when you

first start your PK-900. Type DFROM to display the ALL/NONE/YES_list/NO_list

status of station's call signs whose packets will or will not be repeated.

To prevent all stations from digipeating through Radio Port 1 of your station,

type DFROM NONE.

To permit one or more specific stations to digipeat through Radio Port 2 of your

station, type DFROM /YES (followed by a list of calls signs). Packets will be

digipeated only from stations whose call signs are listed.

To prevent one or more specific stations to digipeat through Radio Port 1 of

your station, type DFROM NO (followed by a list of call signs). Packets will

not be digipeated from stations whose call signs are listed.

Clear DFROM with "%" "&" or "OFF" as arguments, or type DFROM ALL/ALL.

________________________________________________________________________________

DIDdle: ON|OFF Default: ON

Mode: Baudot, ASCII Host: DD

_________________________________ Parameters: __________________________________

ON - In Baudot, the PK-900 will send the LTRS character when idling.

In ASCII, the PK-900 sends the NULL (00) character.

OFF - No characters are sent when idling in transmit.

________________________________________________________________________________

In RTTY modes, it may be desirable to continue sending data while paused at the

keyboard. With DIDDLE on, the PK-900 sends idle characters when waiting for

keyboard entry.

3/93 A-43

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands