Timewave PK-900 Operating Manual Download Page 232

Page: 232 / 392

________________________________________________________________________________

Help Immediate Command

Mode: Command Host: Not Supported

________________________________________________________________________________

While in Command Mode, type the command "H" to read the abbreviated on-line HELP

file. Your monitor displays the following brief list:

Help:

AScii AMtor PAcket

BAudot ARq Connect

MOrse AList Disconn

DISPlay FEc MHeard

CALibrate AChg CStatus

NAvtex SIgnal FAx TDm

ANalog

PACTOr PTConn PTSend PTList

DIRect 2DIRect VOltage

CONVerse Trans

Opmaode Xmit Rcve Lock

RESTART TESET MDCHECK TClear

You can enter Command Mode at any time to list the HELP text.

________________________________________________________________________________

HEReis "n" Default: $02 <CTRL-B>

Mode: Baudot, ASCII, AMTOR and PACTOR Host: HR

_________________________________ Parameters: __________________________________

"n" - Is the hex representation ($01-$7F) of the character that causes the

AAB string to be sent in the middle of transmitted text.

________________________________________________________________________________

If you wish to send your own AAB string for identification during a transmission

simply enter the HEREIS character (default <CTRL-B>). Also see the command AAB.

________________________________________________________________________________

HId ON|OFF/ON|OFF Default: OFF/OFF

Mode: Packet Host: HI

_________________________________ Parameters: __________________________________

ON - Your PK-900 sends HDLC identification as a digipeater.

OFF - Your PK-900 does not send HDLC identification.

________________________________________________________________________________

Set HID ON to force your PK-900 to send an ID packet every 9.5 minutes when

it's being used as a digipeater. Otherwise leave HID OFF (default).

HID is settable for either Radio Port on the PK-900 since it is not likely

both ports will be performing the digipeater function.

This identification consists of a UI-frame with your station identification

(MYCALL) and MYALIAS in the data field. The packet is addressed to "ID".

NOTE: You cannot change the 9.5-minute automatic interval timing.

3/93 A-54

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands