manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 36 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 36

 

3.3.6     Wiring Your HF Transceiver for Direct CW Keying 

 

          The PK-900 can directly key CW with HF and VHF multi-mode  

          transceivers.  This requires that a cable be wired from the CW KEY OUT  

          jack on the PK-900's rear panel to the CW keying input of your  

          transceiver on the correct Radio Port.  Refer to the instructions  

          below and Figure 3-3 to wire the PK-900 side of the cable. 

 

 

 

                  Figure 3-3:  Direct CW Keying Cable diagram 

 

 

          1.   Locate a 5 pin DIN connector from the PK-900's accessory bag. 

 

          2.   Consult your radio's instruction manual to determine if your  

               radio uses negative (Grid Block) or positive keying polarity.   

               Locate some shielded audio cable from Radio Shack or other cable   

               house and solder the DIN connector to the cable as shown above. 

 

          3.   Locate the connector for the CW keying input to your transceiver.   

               These are often supplied in your transceiver's accessory kit. 

 

          4.   Wire the transceiver connector as per the instructions in your  

               transceiver's manual for a "Straight key". 

 

          Connect the shielded cable you just wired from the PK-900's positive  

          or negative keying output to your radio's CW key input connector. 

          See the Specifications on page 1-4 for maximum limits. 

 

3.3.7     Connections for Direct FSK Operation on RTTY 

 

          Some HF SSB radios provide direct FSK (Frequency-Shift Keying) for  

          RTTY operation.  Direct FSK can be an advantage when using RTTY and  

          AMTOR and can sometimes help in HF packet operation.  FSK operation  

          may be helpful if your transceiver can switch in filters.  Be cautious  

          of narrow filters as they can limit your data rate.  Direct FSK is not  

          always recommended for data speeds above 110 bauds.  Consult your  

          transceiver's manual for further recommendations on direct FSK. 

 

          To install and operate your PK-900 and radio in the FSK mode: 

 

          1.   Connect a shielded cable from the PK-900's FSK  receptacle,   

               pins 1 or 4, to the radio's FSK input for radio port 1.  Pins 3   

               or 5 are the FSK outputs for radio port 2. 

 

          NOTE:     Polarity of the FSK signals is not standardized by the radio  

                    manufacturers.  We have observed that Icom radios most often   

                    use FSKN (pins 3 and 4), while Kenwood radios most often use  

                    FSKR (pins 1 and 5).  Consult your transceiver's manual to  

                    identify the proper polarity. 

 

1/93                                    3-6 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments