manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 367 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 367

PK-900/DSP Upgrade Kit

Thank you for purchasing the PK-900/DSP upgrade. Here are the tools you will
need:

Wire Cutters
Phillips Screwdriver
Needle node pliers
Flat head screwdriver
Solder pencil and solder
Solder sucker tool or solder wick for cleaning the pads on C69, C89 and

 the U55 “VIA”

Please check the contents of the kit at this time. You should have received:

PK-900/DSP Upgrade board assembly
Package with 1 metal and 1 plastic standoff
PK-900/DSP installation instructions (This document – 4 pages)
Manual supplement request form (1 page)
Warranty card

Clean off an area to work on your PK-900. You should take standard static
electric precautions when working on any ham equipment.

Here are the steps in the upgrade procedure:

1) Remove Power

2)  Remove 4 screws holding chassis top

3)  Locate and remove U36, U37 and U44 (See figure A.)

Slide the flat blade of the screwdriver under the chip and elevate carefully. Do
the same thing at the other end of the IC and it will pop out cleanly. BE SURE
the screwdriver is between the IC and the chip socket, NOT between the chip
socket and the board

4)  Locate and remove C69 and C89 (see figure B)

We recommend that when you remove the capacitors that they be removed
by clipping the leads of the capacitor close to the body of the capacitor. Then
while holding the lead with the needle nose pliers CAREFULLY heat the
solder just until the lead can be removed without force. Be very careful not to
pull the barrel from the board by pulling before the solder flows. DO NOT
OVERHEAT. The hole can then be cleaned with the solder sucker tool or
solder wick.

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments