Timewave PK-900 Operating Manual Download Page 118 | Manualshive

Page: 118 / 392

background image

If the tuning indicator looks like the one below, the frequency

from your speaker is too low for the PK-900 to copy the signal.

Slowly tune the VFO and make the frequency higher.

——————————————————————————————————————————————————————————————

MARK |

| SPACE

——————————————————————————————————————————————————————————————

Tuning too low for discriminator indicator (BAR 0)

——————————————————————————————————————————————————————————————

|

|

——————————————————————————————————————————————————————————————

Tuning too low for magic eye indicator (BAR 3)

——————————————————————————————————————————————————————————————

|

|

——————————————————————————————————————————————————————————————

Tuning too low for center tune indicator (BAR 2)

If the tuning indicator looks like the one below, the frequency

from your speaker is too high for the PK-900 to copy the

signal. Slowly tune the VFO and make the frequency lower.

——————————————————————————————————————————————————————————————

MARK |

| SPACE

——————————————————————————————————————————————————————————————

Tuning too high for discriminator indicator (BAR 0)

——————————————————————————————————————————————————————————————

|

|

——————————————————————————————————————————————————————————————

Tuning too high for magic eye indicator (BAR 3)

——————————————————————————————————————————————————————————————

|

|

——————————————————————————————————————————————————————————————

Tuning too high for center tune indicator (BAR 2)

o Adjust the PK-900 front panel THRESHOLD control so that the DCD

LCD lights when a properly tuned FEC AMTOR station is being

received.

After you have an FEC AMTOR station tuned in, you should start seeing

the copy on your screen. If you have tuned in "chirping" ARQ AMTOR

stations, you will not print anything until you enter the ALIST mode.

If you just want to receive, see Chapter 10 on SIGNAL IDENTIFICATION.

3/93 7-4

«
...
116
117
118
119
120
...
»

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments

Related manuals for PK-900

Brand: Walchem Pages: 10

Brand: Tapeswitch Pages: 13

Brand: Banner Pages: 15

Brand: bar Pages: 2

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

ECL Comfort 300

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 8

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 12

ECL Comfort 110

Brand: Danfoss Pages: 8

ECL Comfort 100M

Brand: Danfoss Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands