Timewave PK-900 Operating Manual Download Page 96

Page: 96 / 392

5.6 Sample MailDrop Session - MailDrop SYSOP's Point of View

Here is a transcription of the entire session described in the

previous section, exactly as it would appear to the MailDrop's

operator (SYSOP). We're assuming that the MDMON command is set to ON.

When MDMON is ON, you have the ability to supervise the activities of

any station logged on to your MailDrop and - if needed - take any

corrective action.

WX1AAA>WX2BBB <C,P>

You have mail

[AEA PK-900] 16508 free (A,B,H,J,K,L,R,S,V,?) >

*** CONNECTED to WX1AAA (Maildrop)

Msg# Size To From @ BBS Date Time Title

6 PN 184 WX1AAA WX2BBB 01-Jun-90 20:15 Hello Joe

5 BY 287 ALL WX2BBB 01-Jun-90 18:42 Question

4 BY 178 QST WX2BBB 01-Jun-90 17:30 Mailbox

1 BY 56 ALL WX2BBB 01-Jun-90 10:22 APLINK

[AEA PK-900] 16508 free (A,B,H,J,K,L,R,S,V,?) >

R 6

Msg# Size To From @ BBS Date Time Title

6 PN 184 WX1AAA WX2BBB 01-Jun-90 20:15 Hello Joe

Hello Joe. Did you get the notice

about next month's meeting of the

Radio Society at the Firehouse?

Will you be going? - I need a ride.

73.

[AEA PK-900] 16508 free (A,B,H,J,K,L,R,S,V,?) >

K 6

*** Done.

[AEA PK-900] 16704 free (A,B,H,J,K,L,R,S,V,?) >

S WX2BBB

Subject:

I WILL BE GOING

Enter message, ^Z (CTRL-Z) or /EX to end

YEAH, I GOT THE MAILING AND WILL

BE GLAD TO PICK YOU UP. WHAT TIME

DO YOU WANT ME THERE? IS MARY

GOING? CUL. WX1AAA

/EX

[AEA PK-900] 16508 free (A,B,H,J,K,L,R,S,V,?) >

*** DISCONNECTED

1/93 5-10

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Timewave PK-900, Operating Manual, Page: 96 / 392

Search results

Summary of Contents for PK-900

Reviews: