Timewave PK-900 Operating Manual Download Page 280

Page: 280 / 392

UBIT 7: OFF: In Morse receive, the character ..-- prints as a "^".

ON: In Morse, the character ..-- prints as a <Carriage Return>.

UBIT 8: Not used in the PK-900.

UBIT 9: ON: In AMTOR or PACTOR a received WRU character (FIGS-D) will cause

the Auto-Answerback text to be sent regardless of the setting

of WRU.

This is subject to the setting of the CODE command.

OFF: In AMTOR or PACTOR a received WRU character (FIGS-D) will have

no effect.

UBIT 10: OFF: Polling in the HOST mode is subject to HPOLL and must be done for

all changes in status.

ON: Status changes (e.g. Idle to Tfc) in AMTOR, FAX, TDM, PACTOR or

NAVTEX causes the PK-900 to issue the following host block:

SOH $50 n ETB

where n is $30-36, the same number that the OPMODE command

furnishes. This block is subject to HPOLL.

UBIT 11: ON: A "Connected" message appears when an ARQ link is first

established using seven-character SELCALLs (CCIR 625).

OFF: No Connected message appears at the start of ARQ communications.

UBIT 12: OFF: The Packet Morse ID (MID) is ON/OFF keying of the low tone.

ON: The Packet Morse ID is sent in 2-tone FSK with the low tone being

key-down and the high tone representing key-up. Use this setting

to keep other stations from sending a packet during the Morse ID.

UBIT 13: OFF: MailDrop Connect status messages are always sent to the local

user, regardless of the setting of MDMON.

ON: Remote user dialog and Connect status messages with the MailDrop

are shown only if MDMON is ON.

UBIT 14: OFF: In Packet, the transmit buffer for data sent from the computer to

the PK-900 is limited only by available PK-900 memory.

ON: In Packet, the serial flow control will permit only a maximum of

7 I-frames to be held by the PK-900 before transmission. This

solves a problem with the YAPP binary file transfer program which

relies on a small TNC transmit buffer to operate correctly.

UBIT 15: Not used in the PK-900.

UBIT 16: Not used in the PK-900.

UBIT 17: OFF: Morse, Baudot, ASCII and AMTOR transmissions start when

commanded by the user or an application program.

ON: Morse, Baudot, ASCII, PACTOR and AMTOR transmissions will not

begin until the channel is clear of signals. The channel is

considered clear when both the DCD and the Squelch input

(if used) are inactive. The PERSIST and SLOTTIME delay

functions are used if PPERSIST is ON, otherwise the DWAIT time

is used.

1/93 A-102

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands