Timewave PK-900 Operating Manual Download Page 17

Page: 17 / 392

1.4 PK-900 Specifications

As part of its program of product improvement, AEA reserves the right

to make changes in this product's specifications. Changes may also be

made to the information in this document and incorporated in revisions

to this manual. Prices and specifications are subject to change

without notice or obligation.

1.4.1 Modem Characteristics

Port 1:

Demodulator: Programmable Limiter-discriminator type,

preceded by an 8-pole Chebychev 0.5-dB

ripple bandpass filter.

Receive Band-pass: Automatically switched by operating mode

VHF packet: Center frequency 1700 Hz,

HF (except CW) Center frequencies: 1700, 2210,

2337.5 or 2550 Hz depending on

frequency shift chosen.

Bandwidth: 200, 470, 725, or 1150,

optimized for operating mode.

CW Center frequency 750 Hz,

bandwidth 200 Hz

Modulator Crystal controlled, 1 Hz step

programmable, phase-continuous, Direct

Digital Synthesis sine wave generator

Output Level: 5 to 100 millivolts RMS into 600 Ohms,

adjustable by a rear-panel control

Port 2:

Modulator/Demodulator AMD 7910 'World Chip' FSK Modem

Modem Tones: Bell 103 and 202

Output Level: 5 to 100 millivolts RMS into 600 Ohms,

adjustable by a rear-panel control

Options: 9600 baud direct FSK packet modem

(G3RUH/K9NG compatible)

Grey scale HF FAX receiving program

1.4.2 Processor System

Protocol conversion: Zilog Z-180 (64180) microprocessor

RAM: 64 Kilobytes

ROM: Up to 256 Kilobytes of ROM may be used

Display and memory ARQ

processor: 68HC05B4

DSS processor: 68HC05C4

Hardware HDLC: Zilog 8530 SCC

8/93 1-3

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands