Timewave PK-900 Operating Manual Download Page 293

Page: 293 / 392

COMMAND DEFAULT FUNCTION

KISSAddr 0 Sets the Address used in extended KISS mode

LAstmsg Immediate Command Sets/shows the Last maildrop message number

LEftrite ON Sets left-to-right Scan direction for FAX

LIte OFF/OFF Enables AEA's Packet Lite HF protocol

Lock Immediate Command Locks Morse speed/ forces lower case in RTTY

MAildrop OFF Enables the Packet MailDrop for remote users

MARK 1200 Sets or displays the current Mark frequency

MARsdisp OFF Translates received LTRS & FIGS characters

MAXframe 4/4 Sets a maximum of un-ACK'd packet frames

MBEll OFF/OFF Rings bell when packet station heard

MBx none, (calls) Monitors packet channel without headers

MCon 0/0 (zero) Monitors packets while connected (0-6)

MDCheck Immediate Command Allows you to check into your own MailDrop

MDigi OFF Monitors packet frames that you digipeat

MDMon OFF Monitors stations using your MailDrop

MDPrompt (see text) Sets an 80 character MailDrop message prompt

MFIlter $80 Filters received ASCII characters

MFrom ALL/ALL (calls) Monitors packets FROM other packet stations

MHeard Immediate Command Displays call packet signs heard

MId 0/0 Enables a Morse ID to be sent in packet

MMsg OFF Enables the MailDrop sign on message

MODem 11/4 Sets the current radio port modems

Monitor 4/4 Sets the packet Monitor mode level (0-6)

MOrse Immediate Command Starts the Morse mode, unlock speed

MProto OFF/OFF Enables monitoring of all packet protocols

MRpt ON/ON Shows digipeaters in packet headers

MSPeed 20 Sets the Morse speed in WPM (5-99)

MStamp OFF Time-stamps monitored packet frames

MTExt (see text) Sets a 120 character MailDrop sign-on message

MTo None/None (Calls) Monitors packets TO other station callsigns

MWeight 10 Sets the Morse transmit dot weighting

MXmit OFF Monitors transmitted packet frames

MYAlias None/None Sets the alternate MYCALL for digipeating

MYALTcal None; enter yours Sets the alternate AMTOR SELCAL

MYCall PK900/PK900 Sets YOUR packet call sign (MUST BE ENTERED)

MYIdent None; enter yours Sets your CCIR-625 7-character AMTOR SELCAL

MYGate None; enter yours Sets the port-1 port-2 packet gateway call

MYMail None; enter yours Sets your Packet MailDrop callsign

MYPTcall None; enter yours Sets your PACTOR callsign

MYSelcal None; enter yours Sets your AMTOR SELCAL, 4 letters

NAVMsg ALL Determines which NAVTEX messages you monitor

NAVStn ALL Determines which NAVTEX stations you monitor

NAvtex Immediate Command Starts the NAVTEX/AMTEX receive mode

NEwmode ON Returns to Command mode at disconnect

NOmode OFF Sets NO mode changes (eg. cmd: to CONVERSE)

NUCr OFF Sends Nulls to terminal after <CR>

NULf OFF Sends Nulls to terminal after <LF>

NULLs 0 (zero) Sets the number of for NUCR and NULF

Nums Immediate Command Forces FIGS case in Baudot, AMTOR and TDM

OK Immediate Command Transfers to mode after Signal Identification

Opmode Immediate Command Displays current PK-900 operating mode

PAcket Immediate Command Starts the Packet Mode

PACLen 128/128 Sets the number user data bytes in a packet

3/93 3

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Timewave PK-900, Operating Manual, Page: 293 / 392

Search results

Summary of Contents for PK-900

Reviews: