manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 164 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 164

 

11.6.5    LCD Status and Mode Indicator 

 

          The front panel LCD display provides mode and status information at a  

          glance. This is especially useful in PACTOR operation.  The following  

          describes typical status indications you will see. 

 

          Type "PTCONN (CALLSIGN of distant station)."  The status changes to: 

 

             LCD:   PACTOR ARQ PHASE,  TX and CONNECT 

 

          This shows that your transmitter is in the SEND condition, in the  

          "connect" part of an ARQ connect call.  Your transmitter will key on  

          and off sending the distant station's connect request. 

 

          As soon as your PK-900 is synchronized with the distant station, the  

          status changes to: 

 

             LCD:   PACTOR ARQ TFC, TX and CONNECTED 

 

          Verify the link by typing <Enter> a few times and watch the display.   

          Your traffic will now begin to flow as you type characters.  If EAS  

          (Echo As Sent) is set ON, your typed characters are displayed as they  

          are sent.  The status will change back and forth from IDLE and  

          TRAFFIC whenever your typing pauses and resumes. 

 

          When errors occur on the link and the distant station sends REQUEST  

          (request for repeat), the status will show: 

 

             LCD:   PACTOR ARQ ERROR and/or REQUEST, TX and CONNECTED 

 

               ERROR:    Your PK-900 has detected errors in the signals  

                         received from the distant station. 

 

               REQUEST:  Your PK-900 has received a "request for repeat"   

                         code from the distant station. 

 

          If the link fails and you lose synchronization with the distant 

          station the PK-900 goes to standby and the status shows: 

 

             LCD:   PACTOR, STANDBY 

 

 

          For the unproto mode:  

 

          After typing" PTSEND", to start an unproto transmission, your PK-900  

          displays the system status: 

 

             LCD:   PACTOR FEC IDLE, TX 

 

          As you send your traffic the status will change back and forth from  

          IDLE to TRAFFIC.  Whenever you stop typing, the IDLE status is  

          displayed. 

 

 

 

 

 

 

3/93                                   11-8 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments