Timewave PK-900 Operating Manual Download Page 20

Page: 20 / 392

2.2.1 Connecting Power

MAKE SURE YOUR POWER SUPPLY IS OFF AND UNPLUGGED BEFORE WIRING

1. If you are using the AEA AC-4 or Timewave AC-5, skip to 5.

Otherwise, locate the PK-900 Power Cable in the accessory bag

. Strip off just enough insulation from the ends to connect it to

your 13-14 Volt DC regulated power supply.

2. The Center pin of the coaxial power plug is POSITIVE. Connect

the lead with the White stripe to the POSITIVE (+) lead on your

power supply. Check this with an Ohm-meter if you have one.

3. Connect the solid Black (GROUND) lead to the NEGATIVE (-) lead of

your power supply.

4. Connect the power plug to the 13 VDC Power Receptacle on the left

rear of the PK-900. DO NOT CONNECT YOUR COMPUTER YET.

5. Plug in your power supply or AC-4 and turn on power. Turn on

the PK-900 by depressing the Power Switch on the front of the

unit. At power-on, the LCD Status display on the left should

light. At this point, turn OFF the PK-900 and move on to

section 2.3.

If the Status display does not light, then re-check the above steps to

insure that 12-14 VDC is available at the power plug and the center

pin is POSITIVE.

If the Status display lights, and status indicators other than the

DCD indicators are displayed, then the PK-900 has already been

initialized. If the PK-900 has been initialized it is ready to

communicate with a computer or terminal at a specific baud rate

(probably 300, 1200, 2400, 4800 or 9600 baud). If you know what

this baud rate is then you should continue with the installation at

section 2.3 keeping this in mind.

If you do not know the baud rate the PK-900 has been initialized to

then you should reset the PK-900 by holding the rear-panel RESET

switch at the same time you turn on the power switch. After this is

done, no status indicators on the LCD Status display should be on

with the possible exception of either or both of the two DCD

indicators.

If the above did not produce the blank status indication, (ignoring

the DCD indicators) contact the Timewave Technical Support Department

as described in the front of this manual.

Figure 2-1 PK-900 Front Panel Controls and indicators

1/93 2-2

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands