manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 324 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 324

Original AEA Warranty – obsolete – PK-900 is no longer in production (12/17/02)

LIMITED WARRANTY

ADVANCED ELECTRONIC APPLICATIONS, INC. warrants to the original

purchaser that this product shall be free from defects in

material or workmanship for one year from the date of original

purchase.  In order to obtain warranty service: 1) Complete and

mail the warranty registration card within 10 days to Advanced

Electronic Applications, Inc., and 2) Send written notification

to the address below or telephone as soon as possible after

discovering a possible defect:

Advanced Electronic Applications, Inc.

Attention: Service Department

2006-196th St. S.W.

Lynnwood, WA 98036

(206) 775-7373

The written notification must include a copy of the invoice.

Include a description of the defective part or condition, with

details of the electrical connections to associated equipment and

list such equipment.  Please enclose your name, phone number, and

address.  Shipping charges for any parts or units submitted for

replacement under this warranty must be paid by the purchaser.

Correct maintenance, repair and use are important to insure

proper performance from this product.  Carefully read the

Instruction Manual.  This warranty does not apply to any defect

AEA determines is caused by 1) Improper maintenance or repair,

including the installation of parts or accessories that do not

conform to the quality and specification of the original parts;

2) Misuse, abuse, neglect, or improper installation; 3)

Accidental or intentional damage.  The field installation of

circuits according to the explicit instructions of AEA will not

nullify this warranty.

All implied warranties, if any, terminate one year from the date

of original purchase.  AEA is not responsible for damage to other

equipment or property or any other consequential damages.  Some

states do not allow limitations of how long an implied warranty

lasts or do not allow the exclusion of incidental or

consequential damages, therefore, the above limitations and

exclusions may not apply to you.

This warranty gives specific legal rights.  You may also have

other rights which vary from state to state.

3/93

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments