Timewave PK-900 Operating Manual Download Page 9

Page: 9 / 392

CHAPTER 6 - BAUDOT AND ASCII RTTY OPERATION

Paragraph Page

6.1 Overview................................................... 6-1

6.2 Where to Operate Baudot and ASCII RTTY..................... 6-1

6.2.1 PK-900 Baudot RTTY Parameter Settings................. 6-1

6.2.2 HF Receiver Settings.................................. 6-2

6.2.3 Tuning in Baudot and ASCII Stations................... 6-2

6.3 Transmitter Adjustments.................................... 6-4

6.3.1 Going On The Air...................................... 6-4

6.4 A Typical Baudot RTTY Contact.............................. 6-4

6.4.1 Calling CQ............................................ 6-5

6.4.2 Answering a CQ........................................ 6-5

6.5 Baudot RTTY Operating Tips................................. 6-5

6.5.1 Changing Speed........................................ 6-6

6.5.2 Formatting Your Transmitted and Received Text......... 6-6

6.5.3 Sending a Synchronous Idle or DIDDLE.................. 6-7

6.5.4 Echoing Transmitted characters As Sent................ 6-7

6.5.5 Sending Only Complete Words........................... 6-7

6.5.6 Operating on the Wrong Sideband....................... 6-7

6.5.7 Framing Errors........................................ 6-7

6.5.8 UnShift-On-Space (USOS)............................... 6-7

6.5.9 Operating at Commercial or VHF Wide RTTY Shifts....... 6-8

6.5.10 The CODE Command for International RTTY Compatibility. 6-8

6.5.11 Copying Encoded RTTY Transmissions.................... 6-8

6.6 ASCII RTTY Operation....................................... 6-8

6.6.1 Starting ASCII Operation.............................. 6-8

6.6.2 ASCII RTTY Operating Tips............................. 6-9

6.6.3 Changing ASCII Baud Rates............................. 6-9

6.6.4 Operating at Commercial or Wide ASCII RTTY Shifts..... 6-10

6.6.5 Other RTTY Commands for ASCII Operation............... 6-10

6.7 Simultaneous RTTY and Packet Operation..................... 6-10

6.7.1 Selecting Modems...................................... 6-11

6.7.2 Displaying Received Data.............................. 6-12

6.7.3 Switching Between Ports............................... 6-12

6.7.4 More Thoughts on Port Switching....................... 6-14

1/93 TOC-5

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Timewave PK-900, Operating Manual, Page: 9 / 392

Search results

Summary of Contents for PK-900

Reviews: