Timewave PK-900 Operating Manual Download Page 58

Page: 58 / 392

NAME DESCRIPTION LCD FUNCTION

PHASE TOR Status Indicates synchroniza

tion of the ARQ calling

ARQ listen signal

OVER TOR Status Indicates changeover of

data transmission

direction

TRAFFIC TOR Status Indicates data reception

or transmission.

ERROR TOR Status Indicates reception of

erroneous data

STANDBY TOR Status Lit when not receiving

transmitting

COMPRESS TOR Status Lit when sending or

receiving compressed

data

SYSTEM Column Heading Always on.

HOST System status Indicates system is in

host mode. Used for

PCPackratt program

MULT System Status Lit when multiple con

nections exist

Blinks when receive

buffer is full

TRANSPARENT System Status Indicates transparent

mode.

COMMAND System Status Indicates the PK-900 is

able to accept commands

CONVERSE System Status Lit when the PK-900 is

ready to send data

MAIL Mailbox Status Lit when mailbox

contains information

MARK Bargraph Indicates mark end of

tuning indicator

SPACE Bargraph Indicates space end of

tuning indicator

4.4.2 Automatic Greetings

You can tell your PK-900 to send an automatic greeting (CTEXT) to

any station that connects to you. This can be used to tell others

1/93 4-16

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands