Timewave PK-900 Operating Manual Download Page 277

Page: 277 / 392

________________________________________________________________________________

Trans Immediate Command

Mode: All Host: Not Supported

________________________________________________________________________________

TRANS is an immediate command that switches the PK-900 switch from the Command

Mode to Transparent Mode. The current state of the radio link is not affected.

Transparent Mode is primarily useful for computer communications. In

Transparent Mode "human interface" features such as input editing, echoing of

input characters, and type-in flow control are disabled.

o Use Transparent Mode for transferring binary or other non-text files.

o To exit the Transparent mode, type the COMMAND character (default <CTRL-C>)

three times within the time period set by CMDTIME (default 1 Second).

________________________________________________________________________________

TRFlow ON|OFF Default: OFF

Mode: Transparent Host: TW

_________________________________ Parameters: __________________________________

ON - Software flow control for the computer or terminal RECEIVING data is

activated in Transparent Mode.

OFF - Software flow control for the computer or terminal RECEIVING data is

disabled in Transparent Mode.

________________________________________________________________________________

When TRFLOW is ON, the type of flow control used by the computer RECEIVING data

in Transparent Mode is determined by how START and STOP are set.

When TRFLOW is OFF, only "hardware" flow control (RTS, DTR) is available to the

computer RECEIVING data from the PK-900 in Transparent Mode.

If TRFLOW is ON, and START and STOP are set to values other than zero, software

flow control is enabled for the user's computer or terminal. The PK-900

responds to the user START and user STOP characters while remaining transparent

to all other characters from the terminal.

________________________________________________________________________________

TRIes "n" Default: 0

Mode: Packet Host: TI

_________________________________ Parameters: __________________________________

"n" - 0 to 15 specifies the current RETRY level on the selected input

channel.

________________________________________________________________________________

TRIES retrieves (or forces) the count of "retry counter" on the data channel

presently selected.

If you type TRIES without an argument, the PK-900 returns the current number

of tries if an outstanding unacknowledged frame exists. If no outstanding

unacknowledged frame exists, the PK-900 returns the number of tries required

to get an ACK for the previous frame.

If you type TRIES with an argument the "tries" counter is forced to the entered

value. Using this command to force a new count of tries is not recommended.

3/93 A-99

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands