Timewave PK-900 Operating Manual Download Page 242

Page: 242 / 392

________________________________________________________________________________

MDigi ON|OFF Default: OFF

Mode: Packet Host: MD

_________________________________ Parameters: __________________________________

ON - I and UI frames having your call sign (MYCALL or MYALIAS) as the next

digipeater in the field are displayed, regardless of connected status.

OFF - Normal monitoring as determined by the monitoring mode commands.

________________________________________________________________________________

MDIGI permits you to display packets when another station uses your station as a

digipeater. If you want to monitor ALL traffic that flows through your packet

station, set MDIGI ON.

You may not want to see all the data passing through your station, especially if

many others use you as a digipeater. In this case set MDIGI OFF (default).

________________________________________________________________________________

MDMon ON|OFF Default: OFF

Mode: AMTOR and Packet/MailDrop Host: Mm

_________________________________ Parameters: __________________________________

ON - Monitor a calling station's activity on your MailDrop.

OFF - Normal monitoring as determined by the monitoring mode commands.

________________________________________________________________________________

Set MDMON to ON to monitor activity on your MailDrop.

MDMON permits you to monitor activity on your AMTOR or packet MailDrop showing

you both sides of the QSO. Packet headers are not shown while a caller is

logged on. When no one is connected to your MailDrop, channel activity is

monitored according to the setting of MONITOR.

Set MDMON OFF to cancel MailDrop monitoring. Note that MailDrop connect and

link status messages will be displayed even with MDMON OFF. These status

messages are important and allow you to see who is connected to your MailDrop.

They can be disabled however with the UBIT 13 command. See the UBIT command for

more information .

________________________________________________________________________________

MDPrompt text Default: (see text)

Mode: Packet/PACTOR MailDrop Host: Mp

_________________________________ Parameters: __________________________________

text - Any combination of characters and spaces up to a maximum of 80 bytes.

________________________________________________________________________________

MDPROMPT is the command line sent to a calling station by your MailDrop in

response to a Send message command. The default text is:

"Subject:/Enter message, ^Z (CTRL-Z) or /EX to end"

Text before the first slash is sent to the user as the subject prompt; text

after the slash is sent as the message text prompt. If there is no slash in the

text, the subject prompt is "Subject:" and the text prompt is from MDPROMPT.

3/93 A-64

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Timewave PK-900, Operating Manual, Page: 242 / 392

Search results

Summary of Contents for PK-900

Reviews: