Timewave PK-900 Operating Manual Download Page 37

Page: 37 / 392

2. Connect the FSK lines from the PK-900 to your radio's FSK or

RTTY input in accordance with your radio's requirements.

See Figure 3-4 below.

Figure 3-4 FSK Connector Connections

NOTE: When using FSK, the same power and duty cycle limits apply

as cited earlier for AFSK operation. Consult your radio's

operating manual for any power or transmit time limits.

3.4 PK-900 Configuration Jumpers and Connections

Before operating the PK-900, you must first make sure it is

correctly configured for your radio's PTT. After this has been

checked you should then connect the cables you constructed above.

3.4.1 Push-To-Talk (PTT) Configuration

Before you connect the radio cable(s) you just made to the

PK-900, consult your transceiver's manual for Push-To-Talk keying

polarity. Most transmitters and transceivers made in the last 15

years use Positive PTT keying. However some gear, especially if it

contains vacuum tubes, may use a negative PTT keying voltage.

The PK-900 is configured for positive PTT at the factory so it will

operate with most equipment without changes. However, if necessary,

you can change the polarity of the PTT configuration on either Port 1

or Port 2. Follow these steps:

o Remove four screws from the top of the PK-900 chassis cover and

lift off the cover.

o Locate Jumper posts JMP1 and JMP2 which are about 4 inches in

from the right-rear corner of the PCB.

o JMP1 configures Port 2 and JMP2 configures Port 1.

o When the shorting jumpers are towards the fuse, the port is

configured for Positive (+) PTT. When the shorting jumpers are

towards the center, the port is configured for Negative (-) PTT.

Replace the cover and four screws when you are finished configuring

the polarity of the PK-900 PTT circuit.

1/93 3-7

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands