Timewave PK-900 Operating Manual Download Page 97

Page: 97 / 392

5.6.1 Message Numbers

Any message that is sent to the PK-900 MailDrop by a remote user or

you, the SYSOP, is given a message number. Message numbers start at 1

and over time work their way up to 999 and then wrap back around to 1

again. Sometime it is desirable to reset the message counter. This

can be done with the LASTMSG command which is described in the Command

summary.

5.7 Forwarding and Reverse Forwarding with the PK-900 MailDrop

Forwarding allows your large community Bulletin Board System (BBS) to

automatically connect to your MailDrop and send messages to you.

Similarly, Reverse Forwarding allows your community BBS to connect to

your MailDrop and get messages you wish to send to others.

Forwarding and Reverse Forwarding (or simply Auto-Forwarding) can be

an advantage in a local area. The community BBS can be set to connect

to your MailDrop at times when local traffic is low, such as late at

night. This can spread out the traffic volume on a packet frequency

which can become quite heavy in the "prime time" early evening hours.

Auto-Forwarding is involved and requires the cooperation of both you

and your community BBS Operator. Not all large BBSs will forward to

individual users. Some packet frequencies are so busy forwarding to

other BBSs that they can not forward to individuals. You must contact

the community BBS SYSOP to determine the guidelines in your area.

5.7.1 MailDrop Settings for Auto-Forwarding

The following must all be set properly for Auto-Forwarding to operate.

- Enter your MYCALL. Enter your MYMAIL if you desire to use a

separate call sign for the MailDrop.

- Make arrangements with your local BBS SYSOP to Auto-Forward to

your MailDrop. Make sure you let the him know the MailDrop call

sign you will use. The BBS SYSOP must program his system to

connect to your MailDrop or Auto-Forwarding will not function.

- Enter the call sign of this community BBS in the HOMEBBS command.

- Leave your PK-900 and radio ON THE AIR so that your local BBS

can connect to your MailDrop. If your packet station is not on

when the local BBS tries to connect, the advantage of Auto-

Forwarding is lost and the BBS SYSOP may drop you from the

Forwarding list.

Once the above have been completed, you are ready to receive messages

automatically from your local BBS. The next section describes how to

prepare messages for Reverse Forwarding to the local BBS (HOMEBBS).

1/93 5-11

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands