manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 329 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 329

5

PK-900 Gateway Option Supplement

The commands’ functions are:

B(ye)

This is similar to the Bye command used in the AEA Maildrop and BBS
stations. When a user enters a 

B

, the Gateway will “disconnect.”

C(onnect) 

n

Similar in operation to the 

CONNECT 

command in the packet mode.

(Also used to connect in AMTOR and PACTOR instead of using the

ARQ 

and 

PTCONN 

commands, respectively.)

For a packet connection, the user may connect to your Gateway, then
specify a string of digipeaters:

C W1AW VIA W2XY, W1XXZ

Your Gateway will try to establish a connection with W1AW as the
destination; the user’s callsign will be shown as the source but with a
difference: the user’s SSID is decremented by one to avoid protocol
conflicts on the same frequency.

Here is an example of the frames sent in establishing a typical
connection (with the MONITOR command set to 

5):

USER>GATE [C]

GATE>USER (UA)

GATE>USER [I]:

   +++ N7ML Gateway. Type ? for help.

   de GATE (B,C,D,J,L,N,S,?) >

USER>GATE (RR)

USER>GATE [I]:

   c remote

GATE>USER (RR)

USER-15>REMOTE [C]

REMOTE>USER-15 (UA)

GATE>USER [I]:

   +++ CONNECTED to REMOTE at GATE

USER>GATE (RR)

USER>GATE [I]:

   hello.

GATE>USER (RR)

USER-15>REMOTE [I]:

    hello.

REMOTE>USER-15 (RR)

REMOTE>USER-15 [I]:

    Yes?

GATE>USER [I]:

USER-15>REMOTE (RR)

   Yes?

USER>GATE (RR)

Once the connection is established with the destination station, the
Gateway notifies the user that the connection has been made; it then
goes from the “Command” mode into the “Converse” mode. Now,

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments