Timewave PK-900 Operating Manual Download Page 23

Page: 23 / 392

Follow the installation directions that come with the Terminal

program you wish to use. Once installed on the computer, you

should start the program and set the communication parameters for

the following:

Data Rate = 1200 bits per second (Bauds)

Data bits = 7

Parity = EVEN

Stop bits = 1

Once these settings have been achieved and the correct serial

communications port chosen, you may proceed to section 2.5.

2.4.2 Terminal Programs for the Apple Macintosh

Although you can use almost any terminal program with your Macintosh,

AEA presently sells the MACRATT with FAX program which provides many

features not available in "telephone modem" programs. See your AEA

dealer for information on MACRATT with FAX.

If you already have the MACRATT program, please follow the program

manual and install the software on your Mac. You should also read

through the PACKET OPERATION chapter of the MACRATT manual.

Familiarity with Packet operation of MACRATT will be necessary for

performing a quick check of the PK-900 in section 2.5 of THIS

manual.

As we mentioned above, an AEA program is not required to use the

PK-900. Many terminal programs can be found throughout the amateur

radio community and can be downloaded from Compuserve, GEnie and from

many telephone bulletin boards.

A partial list of Mac programs tested with the PK-900 includes:

MAC TERMINAL, RED RYDER, MICROPHONE, SMARTCOMM II and MOCK TERMINAL

Follow the installation directions that come with the Terminal program

you wish to use. Once installed on the computer, you should start the

program and set the communication parameters for the following:

COMPATIBILITY:

1200 bauds, 7 bits/character, even parity, Handshake XON/XOFF,

FULL-DUPLEX, Modem connection, "telephone" port.

Once these settings have been achieved, proceed to section 2.5.

2.4.3 Terminal Programs for the Commodore 64, 64C and 128

Although AEA presently sells the COM-PAKRATT with FAX program package

for the PK-232, this program cannot access all the features of the

PK-900. AEA therefore cannot recommend using the COM-PAKRATT

package with the PK-900. If you already have this package, it will

certainly get you started with the PK-900 by using the "Dumb

Terminal" mode. You may wish to find another program which provides

more features than are available in the COM-PAKRATT program in the

Dumb Terminal Mode. Other ideas for terminal programs for the

Commodore-64 series of computers are listed below.

1/93 2-5

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands