Timewave PK-900 Operating Manual Download Page 198

Page: 198 / 392

________________________________________________________________________________

ASPect "n" Default: 2 (576)

Mode: FAX Host: AY

_________________________________ Parameters: __________________________________

"n" - 1 to 6, specifying the number of FAX scan lines the PK-900 displays

out of every 6 lines received.

________________________________________________________________________________

ASPECT controls the aspect ratio of the length to the width of a FAX image by

controlling the number of lines the PK-900 displays out of each 6 received

lines.

On most weather charts, the default of ASPECT 2 keeps the shapes received in the

right proportion. On other transmissions, you may want more resolution.

See the table below for suggested settings.

CCITT IOCs for narrow and wide carriage printers are given for each ASPECT

setting below.

ASPECT CCITT IOC (narrow) CCITT IOC (wide)

1 1100 1788

2 550 (Weather Charts 576) 894

3 367 (Wirephotos 352) 596 (Weather Charts 576)

4 275 (WEFAX Satellite 288) 447

5 220 358 (Wirephotos 352)

6 183 298 (WEFAX Satellite 288)

The Index Of Cooperation, or IOC is an international measure of aspect ratio.

The formula for the CCITT IOC is:

(vertical scan line density) X (horizontal width)

_________________________________________________

3.14159

Weather charts are transmitted at a nominal CCITT IOC of 576. ASPECT 2 is so

close to this that the charts display with no noticeable distortion.

1/93 A-20

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands