Timewave PK-900 Operating Manual Download Page 226

Page: 226 / 392

________________________________________________________________________________

FAx Immediate Command

Mode: Command Host: FA

________________________________________________________________________________

FAX is an immediate command that switches Radio Port 1 of your PK-900 into the

facsimile mode. The FAX mode is available only if the maildrop (or FREE

command) shows at least 3742 bytes free. You must kill MailDrop messages until

the number reaches this level if you wish to operate FAX.

When the PK-900 is in the FAX mode, Packet operation on Radio Port 2 is

disabled. Facsimile transmissions contain so much data, that there is simply

not enough time to handle Packet while facsimile data is being transmitted or

received.

________________________________________________________________________________

FAXNeg ON|OFF Default: OFF

Mode: FAX Host: FN

_________________________________ Parameters: __________________________________

ON - The white and black senses are reversed

OFF - The white and black senses are normal

________________________________________________________________________________

One might use FAXNEG ON when receiving an image consisting mostly of black, as

in a satellite photo. In this case it might help to save your printer ribbon,

as well as accentuating features such as cloud cover.

FAXNEG ON is NOT the same as RXREV ON. RXREV reverses the entire signal,

including the sync pulses. FAXNEG keeps the sync pulses so that they can be

recognized, but reverses the image data.

________________________________________________________________________________

FEc Immediate Command

Mode: AMTOR Mode B Host: FE

________________________________________________________________________________

FEC is an immediate command that starts an AMTOR FEC (Mode B) transmission on

Radio Port 1 of the PK-900. Use FEC for CQ calls in AMTOR. Be sure to

include your SELCALL (MYSELCAL) and MYIDENT code in your CQ message so that the

distant station can call you back in ARQ.

FEC is necessary for all round table AMTOR contacts. When operating in FEC, let

your PK-900 begin each transmission with three to five seconds of idling. The

RTTY practice of transmitting a line of RYRYRY is unnecessary on FEC.

You can signify the end of your FEC transmission by typing the changeover sign

"+?," internationally recognized as the RTTY equivalent of "KKK." However, in

FEC, "+?" is not a software command. You still have to un-key your transmit-

ter (with the RECEIVE, <CTRL> D, or CWID, <CTRL> F, characters or the RCVE,

<CTRL> C R, command) as you would in RTTY.

1/93 A-48

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands