Timewave PK-900 Operating Manual Download Page 335 | Manualshive

Page: 335 / 392

background image

11

PK-900 Gateway Option Supplement

+?

HELLO

HI, NAME IS WALT ...

The other way is to call CQ in Unproto mode and wait for a response:

S

+++ SENDING. TO END, TYPE ’=’.

+?

CQ DE KB7B-15 FROM AMTOR=

KB7B DE N7ML-7 GA+?

+++ CONNECTED TO N7BCD AT N7ML-7

+?

HI, NAME IS WALT. WHAT DO YOU MEAN BY “FROM AMTOR”?

HELLO ...

One thing to keep in mind when accessing VHF packet from AMTOR is that the data
rates on the two radio ports are widely different. In reading a long message from a
packet BBS, the BBS sends the entire message to the Gateway packet port, then may
time out and disconnect before the message has completed transmission on the
AMTOR port. (The Gateway buffers the data so none of the message is lost.)
However, on the packet side, the BBS has wasted time waiting for the next command,
preventing other stations from using the BBS.

L(isten)

Port 2 packet frames are shown to the user as if MONITOR and
MCON were set to a value of

4 (UI, I, C, D, UA and DM frames). Some

TNC monitoring characters are translated for AMTOR:

L

+++ LISTENING ON

KB7B DE N7ML-7 GA+?

P2 N7BCD)W1AW (C)

P2 N7BCD)W1AW (D)

+?

L

+++ LISTENING OFF

KB7B DE N7ML-7 GA+?

S(end)

The Gateway sends UI frames with a destination of “CQ”. The source
field is the user’s callsign with the SSID decremented by one. The
Gateway holds the data characters until the user sends a

(RETURN)

,

whereupon the held data is broadcast.

PACTOR (in) / Packet (out)

With

XGATEWAY

OFF

, your TNC accepts PACTOR calls to your

MYPTCALL

as a normal

PACTOR link-up. With

XGATEWAY

ON

, a PACTOR call to your

MYPTCALL

results in

access to the Gateway and therefore, packet mode on Port 2. (Your

MYGATE

call plays

no part in Gateway access from PACTOR.)

«
...
333
334
335
336
337
...
»

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments

Related manuals for PK-900

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: LANGER EMV-Technik Pages: 48

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: Watlow Pages: 20

Brand: Climatisation Pages: 52

Brand: TECOM Pages: 8

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Brand: K&K Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands