Timewave PK-900 Operating Manual Download Page 235

Page: 235 / 392

________________________________________________________________________________

IO ["n"] Default: none

Mode: All Host: IO

_________________________________ Parameters: __________________________________

"n" - A hexadecimal value used to access the PK-900's memory and I/O

locations, or read values stored at a specified ADDRESS.

________________________________________________________________________________

The IO command works with the ADDRESS command (ADDRESS $aabb) and permits access

to memory and I/O locations. Use the IO command without arguments to read an

I/O location, and with one argument $0 to $FF to write to an I/O location. The

value in ADDRESS is not incremented after using the IO command.

In ADDRESS $aabb, where "aa" (01-FF) is the device address, and "bb" is the

If ADDRESS is set to $00bb, the IO command reads or writes data to the device at

I/O address bb. There is no register set-up before the access. This command is

used as a programmer's aid and is not needed for normal PK-900 use.

________________________________________________________________________________

JUstify "n" Immediate Command

Mode: FAX Host: JU

_________________________________ Parameters: __________________________________

"n" - 0 to 25 specifies the number of half-inches the facsimile image will

be moved closer to the edge of the paper.

________________________________________________________________________________

The number 0-25 is in units of half-inches, or 1/16 of standard (8") paper

width. In most cases entering JUSTIFY n will move the image to the left. If

LEFTRITE is OFF, then JUSTIFY will move the image to the right.

For example if the left-hand edge of the image is 4-1/2 inches away from the

edge of the paper, try entering JUSTIFY 8. This will move the image 4 inches to

the left. If this is not enough, you can always enter JUSTIFY 1, which will

move the image the additional half-inch to the left.

JUSTIFY should only be needed after a manual start has been issued with the LOCK

command in the FAX mode.

________________________________________________________________________________

KILONFWD ON|OFF Default: ON

Mode: Packet/MailDrop Host: KL

_________________________________ Parameters: __________________________________

ON - The PK-900 kills messages after they have been Reverse Forwarded.

OFF - The PK-900 does not kill messages after Reverse Forwarding.

________________________________________________________________________________

Controls the disposition of a message that has been Reverse Forwarded to the

station whose call is in HOMEBBS. If KILONFWD is ON (default), the message is

killed automatically to make room for other messages. If KILONFWD is OFF, the

message's status is changed from "F" to "Y."

1/93 A-57

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands