Timewave PK-900 Operating Manual Download Page 341

Page: 341 / 392

PK-900 Gateway Option Supplement

ARXTOR is defaulted OFF to accommodate old application programs that have no

provision for handling a spontaneous change of modes from PACTOR to AMTOR.

ARXTOR is most versatile when in the PACTOR or PTLIST operating mode.

Here is a summary of the AMTOR/PACTOR mode switching:

Target mode

Original operating mode

detection

AMTOR

ALIST

PACTOR

PTLIST

AMTOR FEC

if RFEC

if ARXT

AMTOR ARQ (MYSELCAL)

always

if ARXT

AMTOR ARQ (MYALTCAL)

always

AMTOR ARQ (MYIDENT)

always

monitor AMTOR ARQ

always

if ARXT

SELFECalways

if ARXT

monitor SELFEC

if SRXALL

if ARXT & SRX

PTCONN

always

monitor PACTOR

always

Note: When automatically switching from PACTOR to AMTOR and back again, the

modem isn’t changed.

ATxrtty “n”

Default: 0

Mode: Morse, Baudot and ASCII

Host: At

Parameters:

“n”

0 to 250, signifying the length of time (in units of 100 msec.) to delay

before sending text.

ATXRTTY allows Morse, Baudot or ASCII characters to be transmitted automati-

cally whenever they’re typed and the TNC is in the Converse mode. When all the

characters in the buffer have been sent, the unit reverts to receive.

The number

n represents the length of time from the last character typed to

the dropping of PTT. This feature makes the repeated use of the commands RCVE

and XMIT unnecessary.

CODe “n”

Default: 0 (International)

Mode: Baudot RTTY, Morse, AMTOR, PACTOR and packet

Host: C1

Parameters:

“n” 0 to 8 specifies a code from the list below.

CODE

Meaning

Morse

Baudot

AMTOR

Packet

TOR Lower Case

—

RX/TX

—

Extended Lower Case

—

RX/TX

—

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands