manualshive.com logo in svg

Timewave PK-900, Operating Manual, Page: 187 / 392

Share
Download
Timewave PK-900 Operating Manual Download Page 187

________________________________________________________________________________ 

     3Rdparty ON|OFF                                             Default: OFF 

     Mode: Packet/AMTOR/PACTOR MailDrop                          Host: 3R 

_________________________________ Parameters: __________________________________ 

 

ON    -   The MailDrop will handle third party traffic. 

OFF   -   The MailDrop will only handle mail to or from MYCALL or MYMAIL. 

________________________________________________________________________________ 

 

If 3RDPARTY is ON, then remote AMTOR, PACTOR and Packet MailDrop users may leave  

messages for any station. 

 

 

________________________________________________________________________________ 

     5Bit                                                   Immediate Command 

     Mode: Command                                          Host: 5B 

________________________________________________________________________________ 

 

5BIT is an immediate command allowing the user to store 5-bit Baudot  

transmissions received on Radio Port 1 then write a program to decrypt codes  

that involve bit inversion or transposition.  In 5BIT, a constant of $40 (64  

decimal) is added to each received 5-bit character to make it a printable ASCII  

character in the range of $40-5F.  All characters are treated this way,  

including CR, LF, LTRS and FIGS. 

 

When the user enters 5BIT, the PK-900 displays "OPMODE now BAUDOT".  This is  

not strictly true; however, the Baudot mode will be displayed on Port 1 of the  

LCD Status display. 

 

RXREV, RBAUD and the MODEM number must be set properly for the monitored  

transmission.  SIGNAL is helpful in determining whether a transmission is 5-bit  

and the settings for RBAUD and RXREV, but typing OK after SIGNAL selects BAUDOT,  

not 5BIT. 

 

Do not change modes directly between BAUDOT, 5BIT and 6BIT.  Go through some  

other mode first, such as Packet.  These commands do not function in 5BIT: 

BITINV, CCITT, CODE, MARSDISP, TRACE, USOS, WRU and XMIT. 

 

 

________________________________________________________________________________ 

     6Bit                                                   Immediate Command 

     Mode: Command                                          Host: 6B 

________________________________________________________________________________ 

 

Same as 5BIT, except that the unit receives a 6-bit code and adds a constant of  

$30 (48 decimal) to yield a range of $30-6F.  RXREV, RBAUD and WIDESHFT must be  

set correctly.  SIGNAL is helpful in determining whether a transmission is 6-bit  

and the settings for RBAUD and RXREV, but OK will not automatically select 6BIT. 

 

When the user enters 6BIT, the PK-900 displays "OPMODE now BAUDOT".  This is  

not strictly true; however, the Baudot mode will be displayed on Port 1 of the  

LCD Status display. 

 

Do not change modes directly between BAUDOT, 5BIT and 6BIT.  Go through some  

other mode first, such as Packet.  These commands do not function in 6BIT: 

BITINV, CCITT, CODE, MARSDISP, TRACE, USOS, WRU or XMIT. 

 

 

 

3/93                                   A-9 

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments